PinePhone USB Driver for Apache NuttX RTOS

Read the articles...

"NuttX RTOS for PinePhone: Simpler USB with EHCI (Enhanced Host Controller Interface)"
"NuttX RTOS for PinePhone: Exploring USB"
"NuttX RTOS for PinePhone: 4G LTE Modem"

We're porting the NXP i.MX RT EHCI USB Driver from Apache NuttX RTOS to PinePhone and Allwinner A64...

"Enhanced Host Controller Interface for USB"

To add the PinePhone USB Driver to our NuttX Project...

cd nuttx/arch/arm64/src/a64
git submodule add https://github.com/lupyuen/pinephone-nuttx-usb
ln -s pinephone-nuttx-usb/a64_ehci.c .
ln -s pinephone-nuttx-usb/a64_ehci.h .
ln -s pinephone-nuttx-usb/a64_usbhost.c .
pushd hardware
ln -s ../pinephone-nuttx-usb/a64_usbotg.h .
popd

Add the USB Driver to Kconfig, Makefile and PinePhone Bringup...

arch/arm64/src/a64/Kconfig
arch/arm64/src/a64/Make.defs
boards/arm64/a64/pinephone/src/pinephone_bringup.c

Configure the NuttX Build...

tools/configure.sh pinephone:lvgl
make menuconfig

Select these options in menuconfig...

Enable "Build Setup > Debug Options > USB Debug Features > USB Error, Warninigs and Info"

And "Battery-related Debug Features > Battery Error, Warnings and Info"
Enable "System Type > Allwinner A64 Peripheral Selection > USB EHCI"
Enable "RTOS Features > Work queue support > Low priority (kernel) worker thread"
Enable "Device Drivers > USB Host Driver Support"
Enable "Device Drivers > USB Host Driver Support > USB Hub Support"

Let's boot the NuttX USB EHCI Driver on PinePhone...

64-Bit Update for EHCI Driver

When PinePhone boots the NuttX USB EHCI Driver, it halts with an Assertion Failure...

_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: chip/a64_ehci.c:4996 task: nsh_main 0x4008b0d0

Here's the assertion, which says that the a64_qh_s struct must be aligned to 32 bytes...

pinephone-nuttx-usb/a64_ehci.c

Line 4996 in b80499b

DEBUGASSERT((sizeof(struct a64_qh_s) & 0x1f) == 0);

Size of the a64_qh_s struct is 72 bytes...

sizeof(struct a64_qh_s)=72

Which isn't aligned to 32 bytes...

pinephone-nuttx-usb/a64_ehci.c

Lines 186 to 200 in b80499b

    
           /* Internal representation of the EHCI Queue Head (QH) */ 
        
           struct a64_epinfo_s; 
        
           struct a64_qh_s 
        
           { 
        
             /* Fields visible to hardware */ 
        
             struct ehci_qh_s hw;           /* Hardware representation of the queue head */ 
        
             /* Internal fields used by the EHCI driver */ 
        
             struct a64_epinfo_s *epinfo; /* Endpoint used for the transfer */ 
        
             uint32_t fqp;                  /* First qTD in the list (physical address) */ 
        
             uint8_t pad[8];                /* Padding to assure 32-byte alignment */ 
        
           };

Because it contains a 64-bit pointer epinfo...

pinephone-nuttx-usb/a64_ehci.c

Line 197 in b80499b

struct a64_epinfo_s *epinfo; /* Endpoint used for the transfer */

How has a64_qh_s changed for 32-bit platforms vs 64-bit platforms?

On 32-bit platforms: a64_qh_s was previously 64 bytes. (48 + 4 + 4 + 8)

On 64-bit platforms: a64_qh_s is now 72 bytes. (48 + 8 + 4 + 8, round up for 4-byte alignment)

In the EHCI Driver we need to align a64_qh_s to 32 bytes. So we pad a64_qh_s from 72 bytes to 96 bytes...

uint8_t pad2[96 - 72]; // TODO: Pad from 72 to 96 bytes for 64-bit platform

Like this...

pinephone-nuttx-usb/a64_ehci.c

Lines 190 to 202 in 2e1f9ab

    
           struct a64_qh_s 
        
           { 
        
             /* Fields visible to hardware */ 
        
             struct ehci_qh_s hw;           /* Hardware representation of the queue head */ 
        
             /* Internal fields used by the EHCI driver */ 
        
             struct a64_epinfo_s *epinfo; /* Endpoint used for the transfer */ 
        
             uint32_t fqp;                  /* First qTD in the list (physical address) */ 
        
             uint8_t pad[8];                /* Padding to assure 32-byte alignment */ 
        
             uint8_t pad2[96 - 72]; // TODO: Pad from 72 to 96 bytes for 64-bit platform 
        
           };

Which fixes the Assertion Failure.

What about other structs?

To be safe, we verified that the other Struct Sizes are still valid for 64-bit platforms...

pinephone-nuttx-usb/a64_ehci.c

Lines 4999 to 5004 in 2e1f9ab

    
           DEBUGASSERT(sizeof(struct ehci_itd_s) == SIZEOF_EHCI_ITD_S);//// 
        
           DEBUGASSERT(sizeof(struct ehci_sitd_s) == SIZEOF_EHCI_SITD_S);//// 
        
           DEBUGASSERT(sizeof(struct ehci_qtd_s) == SIZEOF_EHCI_QTD_S);//// 
        
           DEBUGASSERT(sizeof(struct ehci_overlay_s) == 32);//// 
        
           DEBUGASSERT(sizeof(struct ehci_qh_s) == 48);//// 
        
           DEBUGASSERT(sizeof(struct ehci_fstn_s) == SIZEOF_EHCI_FSTN_S);////

Here are the Struct Sizes...

a64_ehci_initialize: sizeof(struct a64_qh_s)=72
a64_ehci_initialize: sizeof(struct a64_qtd_s)=32
a64_ehci_initialize: sizeof(struct ehci_itd_s)=64
a64_ehci_initialize: sizeof(struct ehci_sitd_s)=28
a64_ehci_initialize: sizeof(struct ehci_qtd_s)=32
a64_ehci_initialize: sizeof(struct ehci_overlay_s)=32
a64_ehci_initialize: sizeof(struct ehci_qh_s)=48
a64_ehci_initialize: sizeof(struct ehci_fstn_s)=8

We need to fix this typo in NuttX: SIZEOF_EHCI_OVERLAY is defined twice...

https://github.com/apache/nuttx/blob/master/include/nuttx/usb/ehci.h#L955-L974

Halt Timeout for USB Controller

The NuttX USB EHCI Driver fails with a timeout when booting on PinePhone...

a64_usbhost_initialize: TODO: a64_clockall_usboh3
a64_usbhost_initialize: TODO: switch off USB bus power
a64_usbhost_initialize: TODO: Setup pins, with power initially off
usbhost_registerclass: Registering class:0x40124838 nids:2
EHCI Initializing EHCI Stack
a64_ehci_initialize: TODO: a64_clockall_usboh3
a64_ehci_initialize: TODO: Reset the controller from the OTG peripheral
a64_ehci_initialize: TODO: Program the controller to be the USB host controller
a64_printreg: 01c1b010<-00000000
a64_printreg: 01c1b014->00000000
EHCI ERROR: Timed out waiting for HCHalted. USBSTS: 000000
EHCI ERROR: a64_reset failed: 110
a64_usbhost_initialize: ERROR: a64_ehci_initialize failed

(Source)

The timeout happens while waiting for the USB Controller to Halt...

pinephone-nuttx-usb/a64_ehci.c

Lines 4831 to 4917 in 2e1f9ab

    
           /**************************************************************************** 
        
            * Name: a64_reset 
        
            * 
        
            * Description: 
        
            *   Set the HCRESET bit in the USBCMD register to reset the EHCI hardware. 
        
            * 
        
            *   Table 2-9. USBCMD - USB Command Register Bit Definitions 
        
            * 
        
            *    "Host Controller Reset (HCRESET) ... This control bit is used by 
        
            *     software to reset the host controller. The effects of this on Root 
        
            *     Hub registers are similar to a Chip Hardware Reset. 
        
            * 
        
            *    "When software writes a one to this bit, the Host Controller resets its 
        
            *     internal pipelines, timers, counters, state machines, etc. to their 
        
            *     initial value. Any transaction currently in progress on USB is 
        
            *     immediately terminated. A USB reset is not driven on downstream 
        
            *     ports. 
        
            * 
        
            *    "PCI Configuration registers are not affected by this reset. All 
        
            *     operational registers, including port registers and port state 
        
            *     machines are set to their initial values. Port ownership reverts 
        
            *     to the companion host controller(s)... Software must reinitialize 
        
            *     the host controller ... in order to return the host controller to 
        
            *     an operational state. 
        
            * 
        
            *    "This bit is set to zero by the Host Controller when the reset process 
        
            *     is complete. Software cannot terminate the reset process early by 
        
            *     writing a zero to this register. Software should not set this bit to 
        
            *     a one when the HCHalted bit in the USBSTS register is a zero. 
        
            *     Attempting to reset an actively running host controller will result 
        
            *     in undefined behavior." 
        
            * 
        
            * Input Parameters: 
        
            *   None. 
        
            * 
        
            * Returned Value: 
        
            *   Zero (OK) is returned on success; A negated errno value is returned 
        
            *   on failure. 
        
            * 
        
            * Assumptions: 
        
            * - Called during the initialization of the EHCI. 
        
            * 
        
            ****************************************************************************/ 
        
           static int a64_reset(void) 
        
           { 
        
             uint32_t regval; 
        
             unsigned int timeout; 
        
             /* Make sure that the EHCI is halted:  "When [the Run/Stop] bit is set to 
        
              * 0, the Host Controller completes the current transaction on the USB and 
        
              * then halts. The HC Halted bit in the status register indicates when the 
        
              * Host Controller has finished the transaction and has entered the 
        
              * stopped state..." 
        
              */ 
        
             a64_putreg(0, &HCOR->usbcmd); 
        
             /* "... Software should not set [HCRESET] to a one when the HCHalted bit in 
        
              *  the USBSTS register is a zero. Attempting to reset an actively running 
        
              *  host controller will result in undefined behavior." 
        
              */ 
        
             timeout = 0; 
        
             do 
        
               { 
        
                 /* Wait one microsecond and update the timeout counter */ 
        
                 up_udelay(1); 
        
                 timeout++; 
        
                 /* Get the current value of the USBSTS register.  This loop will 
        
                  * terminate when either the timeout exceeds one millisecond or when 
        
                  * the HCHalted bit is no longer set in the USBSTS register. 
        
                  */ 
        
                 regval = a64_getreg(&HCOR->usbsts); 
        
               } 
        
             while (((regval & EHCI_USBSTS_HALTED) == 0) && (timeout < 1000)); 
        
             /* Is the EHCI still running?  Did we timeout? */ 
        
             if ((regval & EHCI_USBSTS_HALTED) == 0) 
        
               { 
        
                 usbhost_trace1(EHCI_TRACE1_HCHALTED_TIMEOUT, regval); 
        
                 return -ETIMEDOUT; 
        
               }

What are 01c1 b010 and 01c1 b014?

01c1 b000 is the Base Address of the USB EHCI Controller on Allwinner A64. (See this)

01c1 b010 is the USB Command Register USBCMD. (Page 18)

01c1 b014 is the USB Status Register USBSTS. (Page 21)

a64_printreg: 01c1b010<-00000000
a64_printreg: 01c1b014->00000000

(Source)

According the log, the driver wrote Command 0 (Stop) to USB Command Register USBCMD. Which will Halt the USB Controller.

Then we read USB Status Register USBSTS. This returns 0, which means that the USB Controller has NOT been halted. (HCHalted = 0)

That's why the USB Driver failed: It couldn't Halt the USB Controller at startup.

Why?

Probably because we haven't powered on the USB Controller? According to the log...

a64_usbhost_initialize: TODO: a64_clockall_usboh3
a64_usbhost_initialize: TODO: switch off USB bus power
a64_usbhost_initialize: TODO: Setup pins, with power initially off
a64_ehci_initialize: TODO: a64_clockall_usboh3
a64_ehci_initialize: TODO: Reset the controller from the OTG peripheral
a64_ehci_initialize: TODO: Program the controller to be the USB host controller

(Source)

And maybe we need to init the USB PHY (Physical Layer)?

How do we power on the USB Controller?

Let's check the U-Boot source code...

PinePhone USB Drivers in U-Boot Bootloader

Let's find the PinePhone USB Driver in the U-Boot Bootloader, to understand how it powers on the USB Controller.

When we search for PinePhone in the Source Code of the U-Boot Bootloader, we find this Build Configuration: pinephone_defconfig

CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-pinephone-1.2"

Which refers to this PinePhone Device Tree: sun50i-a64-pinephone-1.2.dts

#include "sun50i-a64-pinephone.dtsi"

Which includes another PinePhone Device Tree: sun50i-a64-pinephone.dtsi

#include "sun50i-a64.dtsi"
#include "sun50i-a64-cpu-opp.dtsi"
...
&ehci0 { status = "okay"; };
&ehci1 { status = "okay"; };

&usb_otg {
  dr_mode = "peripheral";
  status = "okay";
};

&usb_power_supply { status = "okay"; };
&usbphy { status = "okay"; };

Which includes this Allwinner A64 Device Tree: sun50i-a64.dtsi

usb_otg: usb@1c19000 {
  compatible = "allwinner,sun8i-a33-musb";
  reg = <0x01c19000 0x0400>;
  clocks = <&ccu CLK_BUS_OTG>;
  resets = <&ccu RST_BUS_OTG>;
  interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
  interrupt-names = "mc";
  phys = <&usbphy 0>;
  phy-names = "usb";
  extcon = <&usbphy 0>;
  dr_mode = "otg";
  status = "disabled";
};

usbphy: phy@1c19400 {
  compatible = "allwinner,sun50i-a64-usb-phy";
  reg = 
    <0x01c19400 0x14>,
    <0x01c1a800 0x4>,
    <0x01c1b800 0x4>;
  reg-names = 
    "phy_ctrl",
    "pmu0",
    "pmu1";
  clocks = 
    <&ccu CLK_USB_PHY0>,
    <&ccu CLK_USB_PHY1>;
  clock-names = 
    "usb0_phy",
    "usb1_phy";
  resets = 
    <&ccu RST_USB_PHY0>,
    <&ccu RST_USB_PHY1>;
  reset-names = 
    "usb0_reset",
    "usb1_reset";
  status = "disabled";
  #phy-cells = <1>;
};

ehci0: usb@1c1a000 {
  compatible = "allwinner,sun50i-a64-ehci", "generic-ehci";
  reg = <0x01c1a000 0x100>;
  interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
  clocks = 
    <&ccu CLK_BUS_OHCI0>,
    <&ccu CLK_BUS_EHCI0>,
    <&ccu CLK_USB_OHCI0>;
  resets = 
    <&ccu RST_BUS_OHCI0>,
    <&ccu RST_BUS_EHCI0>;
  phys = <&usbphy 0>;
  phy-names = "usb";
  status = "disabled";
};

ehci1: usb@1c1b000 {
  compatible = "allwinner,sun50i-a64-ehci", "generic-ehci";
  reg = <0x01c1b000 0x100>;
  interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
  clocks = 
    <&ccu CLK_BUS_OHCI1>,
    <&ccu CLK_BUS_EHCI1>,
    <&ccu CLK_USB_OHCI1>;
  resets = 
    <&ccu RST_BUS_OHCI1>,
    <&ccu RST_BUS_EHCI1>;
  phys = <&usbphy 1>;
  phy-names = "usb";
  status = "disabled";
};

Which says that the USB Drivers are...

EHCI0 and EHCI1 (Enhanced Host Controller Interface): "allwinner,sun50i-a64-ehci", "generic-ehci"

usb/host/ehci-generic.c
USB OTG (On-The-Go): "allwinner,sun8i-a33-musb"

usb/musb-new/sunxi.c
USB PHY (Physical Layer): "allwinner,sun50i-a64-usb-phy"

phy/allwinner/phy-sun4i-usb.c

Why so many USB drivers? Let's talk about it...

USB Enhanced Host Controller Interface vs On-The-Go

According to the USB Controller Block Diagram in Allwinner A64 User Manual (Page 583)...

There are two USB Ports in Allwinner A64: USB0 and USB1...

Port USB0 is exposed as the External USB Port on PinePhone
Port USB1 is connected to the Internal LTE Modem

USB Port	Alternate Name	Base Address
Port USB0	USB-OTG-EHCI / OHCI	`0x01C1` `A000` (USB_HCI0)
Port USB1	USB-EHCI0 / OHCI0	`0x01C1` `B000` (USB_HCI1)

(Port USB0 Base Address isn't documented, but it appears in the Memory Mapping (Page 73) of the Allwinner A64 User Manual)

Only Port USB0 supports USB On-The-Go (OTG). Which means if we connect PinePhone to a computer, it will appear as a USB Drive. (Assuming the right drivers are started)

(That's why Port USB0 is exposed as the External USB Port on PinePhone)
Ports USB0 and USB1 both support Enhanced Host Controller Interface (EHCI). Which will work only as a USB Host (not USB Device)

Today we'll talk only about Port USB1 (EHCI / Non-OTG), since it's connected to the LTE Modem.

Power On the USB Controller

Earlier we searched for the USB Drivers for PinePhone and found these...

EHCI0 and EHCI1 (Enhanced Host Controller Interface):

usb/host/ehci-generic.c
USB PHY (Physical Layer):

phy/allwinner/phy-sun4i-usb.c

We disregard the USB OTG Driver because we're only interested in the EHCI Driver (Non-OTG) for PinePhone.

The USB PHY Driver handles the Physical Layer (physical wires) that connect to the USB Controller.

To power on the USB Controller ourselves, let's look inside the USB PHY Driver: sun4i_usb_phy_init

static int sun4i_usb_phy_init(struct phy *phy)
{
  struct sun4i_usb_phy_data *data = dev_get_priv(phy->dev);
  struct sun4i_usb_phy_plat *usb_phy = &data->usb_phy[phy->id];
  u32 val;
  int ret;

  ret = clk_enable(&usb_phy->clocks);
  if (ret) {
    dev_err(phy->dev, "failed to enable usb_%ldphy clock\n",
      phy->id);
    return ret;
  }

In the code above we enable the USB Clocks. We'll explain here...

"USB Controller Clocks"

Then we deassert the USB Reset...

  ret = reset_deassert(&usb_phy->resets);
  if (ret) {
    dev_err(phy->dev, "failed to deassert usb_%ldreset reset\n",
      phy->id);
    return ret;
  }

We'll explain the USB Reset here...

"USB Controller Reset"

TODO: Is PMU is needed for PinePhone Port USB1? If PMU is not needed, we skip this part...

  // `hci_phy_ctl_clear` is `PHY_CTL_H3_SIDDQ`, which is `1 << 1`
  // https://github.com/lupyuen/pinephone-nuttx-usb#usb-controller-configuration
  if (usb_phy->pmu && data->cfg->hci_phy_ctl_clear) {
    val = readl(usb_phy->pmu + REG_HCI_PHY_CTL);
    val &= ~data->cfg->hci_phy_ctl_clear;
    writel(val, usb_phy->pmu + REG_HCI_PHY_CTL);
  }

(FYI: PinePhone Port USB0 is connected to the PMIC, according to PinePhone Schematic Page 6)

PinePhone is sun50i_a64_phy, so we skip this part...

  // Skip this part because PinePhone is `sun50i_a64_phy`
  if (data->cfg->type == sun8i_a83t_phy ||
      data->cfg->type == sun50i_h6_phy) {
    if (phy->id == 0) {
      val = readl(data->base + data->cfg->phyctl_offset);
      val |= PHY_CTL_VBUSVLDEXT;
      val &= ~PHY_CTL_SIDDQ;
      writel(val, data->base + data->cfg->phyctl_offset);
    }

PinePhone is sun50i_a64_phy, so we run this instead...

  } else {
    if (usb_phy->id == 0)
      sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN,
              PHY_RES45_CAL_DATA,
              PHY_RES45_CAL_LEN);

    /* Adjust PHY's magnitude and rate */
    sun4i_usb_phy_write(phy, PHY_TX_AMPLITUDE_TUNE,
            PHY_TX_MAGNITUDE | PHY_TX_RATE,
            PHY_TX_AMPLITUDE_LEN);

    /* Disconnect threshold adjustment */
    sun4i_usb_phy_write(phy, PHY_DISCON_TH_SEL,
            data->cfg->disc_thresh, PHY_DISCON_TH_LEN);
  }

Which will...

Set PHY_RES45_CAL (TODO: What's this?)
Set USB PHY Magnitude and Rate
Disconnect USB PHY Threshold Adjustment

As explained here...

"Set USB Magnitude / Rate / Threshold"

TODO: Is usb_phy->id set to 1 for USB Port 1?

Assume CONFIG_USB_MUSB_SUNXI is undefined. So we skip this part...

#ifdef CONFIG_USB_MUSB_SUNXI
  // Skip this part because `CONFIG_USB_MUSB_SUNXI` is undefined
  /* Needed for HCI and conflicts with MUSB, keep PHY0 on MUSB */
  if (usb_phy->id != 0)
    sun4i_usb_phy_passby(phy, true);

  /* Route PHY0 to MUSB to allow USB gadget */
  if (data->cfg->phy0_dual_route)
    sun4i_usb_phy0_reroute(data, true);

CONFIG_USB_MUSB_SUNXI is undefined, so we run this instead...

#else
  sun4i_usb_phy_passby(phy, true);

  /* Route PHY0 to HCI to allow USB host */
  if (data->cfg->phy0_dual_route)
    sun4i_usb_phy0_reroute(data, false);
#endif

  return 0;
}

Which will...

Enable USB PHY Bypass
Route USB PHY0 to EHCI (instead of Mentor Graphics OTG MUSB)

(phy0_dual_route is true for PinePhone)

sun4i_usb_phy_passby and sun4i_usb_phy0_reroute are defined here...

sun4i_usb_phy_passby
sun4i_usb_phy0_reroute

What's CONFIG_USB_MUSB_SUNXI?

CONFIG_USB_MUSB_SUNXI enables support for the Mentor Graphics OTG / DRC USB Controller...

config USB_MUSB_SUNXI
  bool "Enable sunxi OTG / DRC USB controller"
  depends on ARCH_SUNXI
  select USB_MUSB_PIO_ONLY
  default y
  ---help---
  Say y here to enable support for the sunxi OTG / DRC USB controller
  used on almost all sunxi boards.

(Source)

We assume CONFIG_USB_MUSB_SUNXI is disabled because we won't be using USB OTG for NuttX (yet).

USB Controller Clocks

Earlier we looked at the Source Code for the USB PHY Driver for PinePhone...

"Power On the USB Controller"

And we saw this code that will enable the USB Clocks: sun4i_usb_phy_init

  ret = clk_enable(&usb_phy->clocks);

clk_enable is explained here...

"Enable USB Controller Clocks"

What's usb_phy->clocks?

According to the PinePhone Device Tree, the USB Clocks are...

usb0_phy: CLK_USB_PHY0
usb1_phy: CLK_USB_PHY1
EHCI0: CLK_BUS_OHCI0, CLK_BUS_EHCI0, CLK_USB_OHCI0
EHCI1: CLK_BUS_OHCI1, CLK_BUS_EHCI1, CLK_USB_OHCI1

What are the values of the above USB Clocks?

The USB Clocks are defined in clock/sun50i-a64-ccu.h...

#define CLK_BUS_EHCI0		42
#define CLK_BUS_EHCI1		43
#define CLK_BUS_OHCI0		44
#define CLK_BUS_OHCI1		45
#define CLK_USB_PHY0		86
#define CLK_USB_PHY1		87
#define CLK_USB_OHCI0		91
#define CLK_USB_OHCI1		93

Which are consistent with the values in the PinePhone JumpDrive Device Tree: sun50i-a64-pinephone-1.2.dts

The Allwinner A64 Register Addresses for USB Clocks are defined here...

"Enable USB Controller Clocks"

Here's the definition of USB Clocks in our U-Boot Device Tree: sun50i-a64.dtsi

usbphy: phy@1c19400 {
  reg = 
    <0x01c19400 0x14>,
    <0x01c1a800 0x4>,
    <0x01c1b800 0x4>;
  reg-names = 
    "phy_ctrl",
    "pmu0",
    "pmu1";
  clocks = 
    <&ccu CLK_USB_PHY0>,
    <&ccu CLK_USB_PHY1>;
  clock-names = 
    "usb0_phy",
    "usb1_phy";
    ...

ehci0: usb@1c1a000 {
  reg = <0x01c1a000 0x100>;
  clocks = 
    <&ccu CLK_BUS_OHCI0>,
    <&ccu CLK_BUS_EHCI0>,
    <&ccu CLK_USB_OHCI0>;
    ...

ehci1: usb@1c1b000 {
  reg = <0x01c1b000 0x100>;
  clocks = 
    <&ccu CLK_BUS_OHCI1>,
    <&ccu CLK_BUS_EHCI1>,
    <&ccu CLK_USB_OHCI1>;
  resets = 
    <&ccu RST_BUS_OHCI1>,
    <&ccu RST_BUS_EHCI1>;

(CCU means Clock Control Unit)

What are the USB PHY Reg Values from above?

usbphy: phy@1c19400 {
  reg = 
    <0x01c19400 0x14>,
    <0x01c1a800 0x4>,
    <0x01c1b800 0x4>;
  reg-names = 
    "phy_ctrl",
    "pmu0",
    "pmu1";

According to the Allwinner A64 User Manual (Memory Mapping, Page 73)...

phy_ctrl: 0x01c1 9400 (Offset 0x14)

Belongs to USB-OTG-Device (USB Port 0)
pmu0: 0x01c1 a800 (Offset 0x4)

Belongs to USB-OTG-EHCI (USB Port 0)
pmu1: 0x01c1 b800 (Offset 0x4)

Belongs to USB-EHCI0 (USB Port 1)

USB Controller Reset

Earlier we looked at the Source Code for the USB PHY Driver for PinePhone...

"Power On the USB Controller"

And we saw this code that will deassert the USB Reset: sun4i_usb_phy_init

  ret = reset_deassert(&usb_phy->resets);

reset_deassert is explained here...

"Reset USB Controller"

What's usb_phy->resets?

According to the PinePhone Device Tree, the USB Resets are...

usb0_reset: RST_USB_PHY0
usb1_reset: RST_USB_PHY1
EHCI0: RST_BUS_OHCI0, RST_BUS_EHCI0
EHCI1: RST_BUS_OHCI1, RST_BUS_EHCI1

What are the values of the USB Resets?

The USB Resets are defined in reset/sun50i-a64-ccu.h...

#define RST_USB_PHY0		0
#define RST_USB_PHY1		1
#define RST_BUS_EHCI0		19
#define RST_BUS_EHCI1		20
#define RST_BUS_OHCI0		21
#define RST_BUS_OHCI1		22

Which are consistent with the values in the PinePhone JumpDrive Device Tree: sun50i-a64-pinephone-1.2.dts

The Allwinner A64 Register Addresses for USB Resets are defined here...

"Reset USB Controller"

Here's the definition of USB Resets in our U-Boot Device Tree: sun50i-a64.dtsi

usbphy: phy@1c19400 {
  resets = 
    <&ccu RST_USB_PHY0>,
    <&ccu RST_USB_PHY1>;
  reset-names = 
    "usb0_reset",
    "usb1_reset";
    ...

ehci0: usb@1c1a000 {
  resets = 
    <&ccu RST_BUS_OHCI0>,
    <&ccu RST_BUS_EHCI0>;
    ...

ehci1: usb@1c1b000 {
  resets = 
    <&ccu RST_BUS_OHCI1>,
    <&ccu RST_BUS_EHCI1>;

Enable USB Controller Clocks

Earlier we saw this code that will enable the USB Clocks: sun4i_usb_phy_init

  ret = clk_enable(&usb_phy->clocks);

(USB Clocks usb_phy->clocks are defined here)

clk_enable calls sunxi_set_gate

Which A64 Registers will our NuttX USB Driver set?

Our NuttX USB Driver will set the CCU Registers, defined in Allwinner A64 User Manual, Page 81.

(CCU Base Address is 0x01C2 0000)

Based on the USB Clocks usb_phy->clocks, our NuttX USB Driver will set the following CCU Registers: clk_a64.c

static const struct ccu_clk_gate a64_gates[] = {
  [CLK_BUS_EHCI0]		= GATE(0x060, BIT(24)),
  [CLK_BUS_EHCI1]		= GATE(0x060, BIT(25)),
  [CLK_BUS_OHCI0]		= GATE(0x060, BIT(28)),
  [CLK_BUS_OHCI1]		= GATE(0x060, BIT(29)),
  [CLK_USB_PHY0]		= GATE(0x0cc, BIT(8)),
  [CLK_USB_PHY1]		= GATE(0x0cc, BIT(9)),
  [CLK_USB_OHCI0]		= GATE(0x0cc, BIT(16)),
  [CLK_USB_OHCI1]		= GATE(0x0cc, BIT(17)),

So to enable the USB Clock CLK_BUS_EHCI0, we'll set Bit 24 of the CCU Register at 0x060 + 0x01C2 0000.

This will be similar to setting SCLK_GATING of DE_CLK_REG as described here...

"Initialising the Allwinner A64 Display Engine"

TODO: What about OHCI1_12M_SRC_SEL, OHCI0_12M_SRC_SEL? (Allwinner A64 User Manual Page 113)

Reset USB Controller

Earlier we saw this code that will deassert the USB Reset: sun4i_usb_phy_init

  ret = reset_deassert(&usb_phy->resets);

(USB Resets usb_phy->resets are defined here)

reset_deassert calls...

rst_deassert, which calls...
sunxi_reset_deassert, which calls...
sunxi_set_reset

Which A64 Registers will our NuttX USB Driver set?

Our NuttX USB Driver will set the CCU Registers, defined in Allwinner A64 User Manual, Page 81.

(CCU Base Address is 0x01C2 0000)

Based on the USB Resets usb_phy->resets, our NuttX USB Driver will set the following CCU Registers: clk_a64.c

static const struct ccu_reset a64_resets[] = {
  [RST_USB_PHY0]          = RESET(0x0cc, BIT(0)),
  [RST_USB_PHY1]          = RESET(0x0cc, BIT(1)),
  [RST_BUS_EHCI0]         = RESET(0x2c0, BIT(24)),
  [RST_BUS_EHCI1]         = RESET(0x2c0, BIT(25)),
  [RST_BUS_OHCI0]         = RESET(0x2c0, BIT(28)),
  [RST_BUS_OHCI1]         = RESET(0x2c0, BIT(29)),

So to deassert the USB Reset RST_USB_PHY0, we'll set Bit 0 of the CCU Register at 0x0cc + 0x01C2 0000.

This will be similar to setting DE_RST of BUS_SOFT_RST_REG1 as described here...

"Initialising the Allwinner A64 Display Engine"

NuttX EHCI Driver Starts OK on PinePhone

Earlier the NuttX USB EHCI Driver fails during PinePhone startup...

"Halt Timeout for USB Controller"

Then we discovered how the U-Boot Bootloader enables the USB Clocks and deasserts the USB Resets...

"USB Controller Clocks"
"Enable USB Controller Clocks"
"USB Controller Reset"
"Reset USB Controller"

So we do the same for NuttX. And now the NuttX EHCI Driver starts OK on PinePhone yay! 🎉

This is how we enable the USB Clocks and deassert the USB Resets on PinePhone...

pinephone-nuttx-usb/a64_usbhost.c

Lines 118 to 279 in 0e1632e

    
           #define A64_CCU_ADDR        0x01c20000 /* CCU             0x01c2:0000-0x01c2:03ff 1K */ 
        
           /* Display Engine Clock Register (A64 Page 117) */ 
        
           // #define DE_CLK_REG       (A64_CCU_ADDR + 0x0104) 
        
           // #define CLK_SRC_SEL(n)   ((n) << 24) 
        
           // #define CLK_SRC_SEL_MASK (0b111 << 24) 
        
           // #define SCLK_GATING      (1 << 31) 
        
           // #define SCLK_GATING_MASK (0b1 << 31) 
        
           /* Bus Software Reset Register 1 (A64 Page 140) */ 
        
           // #define BUS_SOFT_RST_REG1 (A64_CCU_ADDR + 0x02c4) 
        
           // #define DE_RST            (1 << 12) 
        
           // Set the bit 
        
           static void set_bit(unsigned long addr, uint8_t bit) 
        
           { 
        
             _info("0x%lx Bit %d\n", addr, bit); 
        
             modreg32(1 << bit, 1 << bit, addr); 
        
           } 
        
           // Enable USB Clocks 
        
           // https://github.com/lupyuen/pinephone-nuttx-usb#usb-controller-clocks 
        
           // https://github.com/lupyuen/pinephone-nuttx-usb#enable-usb-controller-clocks 
        
           static void a64_usbhost_clk_enable(void) 
        
           { 
        
             // usb0_phy: CLK_USB_PHY0 
        
             // 0x0cc BIT(8) 
        
             _info("CLK_USB_PHY0\n"); 
        
             #define CLK_USB_PHY0 (A64_CCU_ADDR + 0x0cc) 
        
             #define CLK_USB_PHY0_BIT 8 
        
             set_bit(CLK_USB_PHY0, CLK_USB_PHY0_BIT); 
        
             // usb1_phy: CLK_USB_PHY1 
        
             // 0x0cc BIT(9) 
        
             _info("CLK_USB_PHY1\n"); 
        
             #define CLK_USB_PHY1 (A64_CCU_ADDR + 0x0cc) 
        
             #define CLK_USB_PHY1_BIT 9 
        
             set_bit(CLK_USB_PHY1, CLK_USB_PHY1_BIT); 
        
             // EHCI0: CLK_BUS_OHCI0, CLK_BUS_EHCI0, CLK_USB_OHCI0 
        
             // 0x060 BIT(28) 
        
             _info("CLK_BUS_OHCI0\n"); 
        
             #define CLK_BUS_OHCI0 (A64_CCU_ADDR + 0x060) 
        
             #define CLK_BUS_OHCI0_BIT 28 
        
             set_bit(CLK_BUS_OHCI0, CLK_BUS_OHCI0_BIT); 
        
             // 0x060 BIT(24) 
        
             _info("CLK_BUS_EHCI0\n"); 
        
             #define CLK_BUS_EHCI0 (A64_CCU_ADDR + 0x060) 
        
             #define CLK_BUS_EHCI0_BIT 24 
        
             set_bit(CLK_BUS_EHCI0, CLK_BUS_EHCI0_BIT); 
        
             // 0x0cc BIT(16) 
        
             _info("CLK_USB_OHCI0\n"); 
        
             #define CLK_USB_OHCI0 (A64_CCU_ADDR + 0x0cc) 
        
             #define CLK_USB_OHCI0_BIT 16 
        
             set_bit(CLK_USB_OHCI0, CLK_USB_OHCI0_BIT); 
        
             // EHCI1: CLK_BUS_OHCI1, CLK_BUS_EHCI1, CLK_USB_OHCI1 
        
             // 0x060 BIT(29) 
        
             _info("CLK_BUS_OHCI1\n"); 
        
             #define CLK_BUS_OHCI1 (A64_CCU_ADDR + 0x060) 
        
             #define CLK_BUS_OHCI1_BIT 29 
        
             set_bit(CLK_BUS_OHCI1, CLK_BUS_OHCI1_BIT); 
        
             // 0x060 BIT(25) 
        
             _info("CLK_BUS_EHCI1\n"); 
        
             #define CLK_BUS_EHCI1 (A64_CCU_ADDR + 0x060) 
        
             #define CLK_BUS_EHCI1_BIT 25 
        
             set_bit(CLK_BUS_EHCI1, CLK_BUS_EHCI1_BIT); 
        
             // 0x0cc BIT(17) 
        
             _info("CLK_USB_OHCI1\n"); 
        
             #define CLK_USB_OHCI1 (A64_CCU_ADDR + 0x0cc) 
        
             #define CLK_USB_OHCI1_BIT 17 
        
             set_bit(CLK_USB_OHCI1, CLK_USB_OHCI1_BIT); 
        
             /* Display Engine Clock Register (A64 Page 117) 
        
              * Set SCLK_GATING (Bit 31) to 1 
        
              *   (Enable Special Clock) 
        
              * Set CLK_SRC_SEL (Bits 24 to 26) to 1 
        
              *   (Clock Source is Display Engine PLL) 
        
              */ 
        
             // clk = SCLK_GATING | CLK_SRC_SEL(1); 
        
             // clk_mask = SCLK_GATING_MASK | CLK_SRC_SEL_MASK; 
        
             // modreg32(clk, clk_mask, DE_CLK_REG); 
        
           } 
        
           // Deassert USB Resets 
        
           // https://github.com/lupyuen/pinephone-nuttx-usb#usb-controller-reset 
        
           // https://github.com/lupyuen/pinephone-nuttx-usb#reset-usb-controller 
        
           static void a64_usbhost_reset_deassert(void) 
        
           { 
        
             // usb0_reset: RST_USB_PHY0 
        
             // 0x0cc BIT(0) 
        
             _info("RST_USB_PHY0\n"); 
        
             #define RST_USB_PHY0 (A64_CCU_ADDR + 0x0cc) 
        
             #define RST_USB_PHY0_BIT 0 
        
             set_bit(RST_USB_PHY0, RST_USB_PHY0_BIT); 
        
             // usb1_reset: RST_USB_PHY1 
        
             // 0x0cc BIT(1) 
        
             _info("RST_USB_PHY1\n"); 
        
             #define RST_USB_PHY1 (A64_CCU_ADDR + 0x0cc) 
        
             #define RST_USB_PHY1_BIT 1 
        
             set_bit(RST_USB_PHY1, RST_USB_PHY1_BIT); 
        
             // EHCI0: RST_BUS_OHCI0, RST_BUS_EHCI0 
        
             // 0x2c0 BIT(28) 
        
             _info("RST_BUS_OHCI0\n"); 
        
             #define RST_BUS_OHCI0 (A64_CCU_ADDR + 0x2c0) 
        
             #define RST_BUS_OHCI0_BIT 28 
        
             set_bit(RST_BUS_OHCI0, RST_BUS_OHCI0_BIT); 
        
             // 0x2c0 BIT(24) 
        
             _info("RST_BUS_EHCI0\n"); 
        
             #define RST_BUS_EHCI0 (A64_CCU_ADDR + 0x2c0) 
        
             #define RST_BUS_EHCI0_BIT 24 
        
             set_bit(RST_BUS_EHCI0, RST_BUS_EHCI0_BIT); 
        
             // EHCI1: RST_BUS_OHCI1, RST_BUS_EHCI1 
        
             // 0x2c0 BIT(29) 
        
             _info("RST_BUS_OHCI1\n"); 
        
             #define RST_BUS_OHCI1 (A64_CCU_ADDR + 0x2c0) 
        
             #define RST_BUS_OHCI1_BIT 29 
        
             set_bit(RST_BUS_OHCI1, RST_BUS_OHCI1_BIT); 
        
             // 0x2c0 BIT(25) 
        
             _info("RST_BUS_EHCI1\n"); 
        
             #define RST_BUS_EHCI1 (A64_CCU_ADDR + 0x2c0) 
        
             #define RST_BUS_EHCI1_BIT 25 
        
             set_bit(RST_BUS_EHCI1, RST_BUS_EHCI1_BIT); 
        
             /* Bus Software Reset Register 1 (A64 Page 140) 
        
              * Set DE_RST (Bit 12) to 1 (De-Assert Display Engine) 
        
              */ 
        
             // modreg32(DE_RST, DE_RST, BUS_SOFT_RST_REG1); 
        
           } 
        
           /**************************************************************************** 
        
            * Public Functions 
        
            ****************************************************************************/ 
        
           /**************************************************************************** 
        
            * Name: a64_usbhost_initialize 
        
            * 
        
            * Description: 
        
            *   Called at application startup time to initialize the USB host 
        
            *   functionality. 
        
            *   This function will start a thread that will monitor for device 
        
            *   connection/disconnection events. 
        
            * 
        
            ****************************************************************************/ 
        
           int a64_usbhost_initialize(void) 
        
           { 
        
             int ret; 
        
             a64_usbhost_clk_enable(); 
        
             a64_usbhost_reset_deassert();

Here's the log...

a64_usbhost_clk_enable: CLK_USB_PHY0
set_bit: 0x1c200cc Bit 8
a64_usbhost_clk_enable: CLK_USB_PHY1
set_bit: 0x1c200cc Bit 9
a64_usbhost_clk_enable: CLK_BUS_OHCI0
set_bit: 0x1c20060 Bit 28
a64_usbhost_clk_enable: CLK_BUS_EHCI0
set_bit: 0x1c20060 Bit 24
a64_usbhost_clk_enable: CLK_USB_OHCI0
set_bit: 0x1c200cc Bit 16
a64_usbhost_clk_enable: CLK_BUS_OHCI1
set_bit: 0x1c20060 Bit 29
a64_usbhost_clk_enable: CLK_BUS_EHCI1
set_bit: 0x1c20060 Bit 25
a64_usbhost_clk_enable: CLK_USB_OHCI1
set_bit: 0x1c200cc Bit 17
a64_usbhost_reset_deassert: RST_USB_PHY0
set_bit: 0x1c200cc Bit 0
a64_usbhost_reset_deassert: RST_USB_PHY1
set_bit: 0x1c200cc Bit 1
a64_usbhost_reset_deassert: RST_BUS_OHCI0
set_bit: 0x1c202c0 Bit 28
a64_usbhost_reset_deassert: RST_BUS_EHCI0
set_bit: 0x1c202c0 Bit 24
a64_usbhost_reset_deassert: RST_BUS_OHCI1
set_bit: 0x1c202c0 Bit 29
a64_usbhost_reset_deassert: RST_BUS_EHCI1
set_bit: 0x1c202c0 Bit 25

(Source)

This log above shows NuttX enabling the USB Clocks and deasserting the USB Resets for...

USB PHY0 and USB PHY1
EHCI0 and OHCI0
EHCI1 and OHCI1

(Yeah this looks excessive. We probably need only USB PHY1, EHCI1 and OHCI1)

Then the NuttX EHCI Driver starts...

a64_usbhost_initialize: TODO: a64_clockall_usboh3
a64_usbhost_initialize: TODO: switch off USB bus power
a64_usbhost_initialize: TODO: Setup pins, with power initially off
usbhost_registerclass: Registering class:0x40124838 nids:2
a64_ehci_initialize: sizeof(struct a64_qh_s)=96
a64_ehci_initialize: sizeof(struct a64_qtd_s)=32
a64_ehci_initialize: sizeof(struct ehci_itd_s)=64
a64_ehci_initialize: sizeof(struct ehci_sitd_s)=28
a64_ehci_initialize: sizeof(struct ehci_qtd_s)=32
a64_ehci_initialize: sizeof(struct ehci_overlay_s)=32
a64_ehci_initialize: sizeof(struct ehci_qh_s)=48
a64_ehci_initialize: sizeof(struct ehci_fstn_s)=8
EHCI Initializing EHCI Stack
a64_ehci_initialize: TODO: a64_clockall_usboh3
a64_ehci_initialize: TODO: Reset the controller from the OTG peripheral
a64_ehci_initialize: TODO: Program the controller to be the USB host controller
a64_printreg: 01c1b010<-00000000
a64_printreg: 01c1b014->00001000
a64_printreg: 01c1b010->00000000
a64_printreg: 01c1b010<-00000002
a64_printreg: 01c1b010->00080b00
a64_ehci_initialize: TODO: Re-program the USB host controller
a64_printreg: 01c1b018<-00000000
a64_printreg: 01c1b014<-0000003f
EHCI HCIVERSION 1.00
a64_printreg: 01c1b004->00001101
EHCI nports=1, HCSPARAMS=1101
a64_printreg: 01c1b008->0000a026
EHCI HCCPARAMS=00a026
a64_printreg: 01c1b028<-40a87fa0
a64_printreg: 01c1b024<-40a95000
a64_printreg: 01c1b010->00080b00
a64_printreg: 01c1b010<-00080b30
a64_printreg: 01c1b010->00080b30
a64_printreg: 01c1b010<-00080b31
a64_printreg: 01c1b050->00000000
a64_printreg: 01c1b050<-00000001
a64_printreg: 01c1b014->00000000
a64_ehci_initialize: TODO: irq_attach
a64_printreg: 01c1b018<-00000037
a64_ehci_initialize: TODO: up_enable_irq
a64_ehci_initialize: TODO: a64_usbhost_vbusdrive
a64_printreg: 01c1b054->00001000
EHCI USB EHCI Initialized
NuttShell (NSH) NuttX-12.0.3
nsh>

(Source)

The log above says that NuttX has successfully started the EHCI Controller. Yay!

EHCI HCIVERSION 1.00
EHCI nports=1, HCSPARAMS=1101
EHCI HCCPARAMS=00a026
EHCI USB EHCI Initialized

Decode EHCI Register Values

In the NuttX Log above, what are the values of the EHCI Registers?

Let's decode the values of the USB EHCI Registers, to make sure that PinePhone is returning the right values on NuttX...

EHCI Log begins with...

EHCI Initializing EHCI Stack
a64_ehci_initialize: TODO: a64_clockall_usboh3
a64_ehci_initialize: TODO: Reset the controller from the OTG peripheral
a64_ehci_initialize: TODO: Program the controller to be the USB host controller

(Source)

Then we see the EHCI Registers and their values...

Write USBCMD: USB Command Register (EHCI Page 18)

(To halt the USB Controller)

Run / Stop (RS, Bit 0) = 0
- Halt the Host Controller
```
a64_printreg: 01c1b010<-00000000
```
Read USBSTS: USB Status Register (EHCI Page 21)

(To verify that USB Controller has been halted)

HCHalted (Bit 12) = 1
- Host Controller has halted
```
a64_printreg: 01c1b014->00001000
```
Read USBCMD: USB Command Register (EHCI Page 18)

(To verify that USB Controller has been halted)

Run / Stop (RS, Bit 0) = 0
- Host Controller has halted
```
a64_printreg: 01c1b010->00000000
```
Write USBCMD: USB Command Register (EHCI Page 18)

(To reset the USB Controller)

Host Controller Reset (HCRESET, Bit 1) = 1
- Reset the Host Controller
```
a64_printreg: 01c1b010<-00000002
```
Read USBCMD: USB Command Register (EHCI Page 18)

Asynchronous Schedule Park Mode Count (Bits 8-9) = 3 (default)

Asynchronous Schedule Park Mode Enable (Bit 11) = 1 (default)

Interrupt Threshold Control (Bits 16-23) = 8 (default)
- 8 micro-frames / 1 ms
```
a64_printreg: 01c1b010->00080b00
a64_ehci_initialize: TODO: Re-program the USB host controller
```
Write USBINTR: USB Interrupt Enable Register (EHCI Page 22)

Disable all interrupts
```
a64_printreg: 01c1b018<-00000000
```
Write USBSTS: USB Status Register (EHCI Page 21)

USB Interrupt (USBINT, Bit 0) = 1 (Reset)

USB Error Interrupt (USBERRINT, Bit 1) = 1 (Reset)

Port Change Detect (Bit 2) = 1 (Reset)

Frame List Rollover (Bit 3) = 1 (Reset)

Host System Error (Bit 4) = 1 (Reset)

Interrupt on Async Advance (Bit 5) = 1 (Reset)
```
a64_printreg: 01c1b014<-0000003f
EHCI HCIVERSION 1.00
```
Read HCSPARAMS: Structural Parameters (EHCI Page 14)

N_PORTS (Bits 0 to 3) = 1 (Number of physical downstream ports)

Number of Ports per Companion Controller (N_PCC, Bits 8 to 11) = 1
- Number of ports supported per companion host controller
Number of Companion Controller (N_CC, Bits 12 to 15) = 1
- Number of companion controllers
```
a64_printreg: 01c1b004->00001101
EHCI nports=1, HCSPARAMS=1101
```
Read HCCPARAMS: Capability Parameters (EHCI Page 15)

64-bit Addressing Capability (Bit 0) = 0
- 32-bit address memory pointers only
Programmable Frame List Flag (Bit 1) = 1
- System software can specify and use a smaller frame list
Asynchronous Schedule Part Capability (Bit 2) = 1
- Support park feature for high-speed queue heads in the Asynchronous Schedule
Isochronous Scheduling Threshold (Bits 4 to 7) = 2

EHCI Extended Capabilities Pointer (EECP, Bits 8 to 15) = 0xA0
```
a64_printreg: 01c1b008->0000a026
EHCI HCCPARAMS=00a026
```
Write ASYNCLISTADDR: Current Asynchronous List Address Register (EHCI Page 25)

Address of the next asynchronous queue head to be executed
```
a64_printreg: 01c1b028<-40a86fa0
```
Write PERIODICLISTBASE: Periodic Frame List Base Address Register (EHCI Page 24)

Beginning address of the Periodic Frame List in the system memory
```
a64_printreg: 01c1b024<-40a97000
```
Read USBCMD: Same as above
```
a64_printreg: 01c1b010->00080b00
```
Write USBCMD: USB Command Register (EHCI Page 18)

Periodic Schedule Enable (Bit 4) = 1
- Use the PERIODICLISTBASE register to access the Periodic Schedule
Asynchronous Schedule Enable (Bit 5) = 1
- Use the ASYNCLISTADDR register to access the Asynchronous Schedule
Asynchronous Schedule Park Mode Count (Bits 8-9) = 3 (default)

Asynchronous Schedule Park Mode Enable (Bit 11) = 1 (default)

Interrupt Threshold Control (Bits 16-23) = 8 (default)
- 8 micro-frames / 1 ms
```
a64_printreg: 01c1b010<-00080b30
```
Read USBCMD: Same as above
```
a64_printreg: 01c1b010->00080b30
```
Write USBCMD: Same as above, plus...

(To start the USB Controller)

Run / Stop (RS, Bit 0) = 1
- Start Host Controller
```
a64_printreg: 01c1b010<-00080b31
```
Read CONFIGFLAG: Configure Flag Register (EHCI Page 25)

Configure Flag (CF, Bit 0) = 0
- Route each port to an implementation dependent classic host controller
```
a64_printreg: 01c1b050->00000000
```
Write CONFIGFLAG: Configure Flag Register (EHCI Page 25)

Configure Flag (CF, Bit 0) = 1
- Route all ports to this host controller
```
a64_printreg: 01c1b050<-00000001
```
Read USBSTS: USB Status Register (EHCI Page 21)

(To verify that USB Controller has been started)

HCHalted (Bit 12) = 0
- Host Controller has started
```
a64_printreg: 01c1b014->00000000
a64_ehci_initialize: TODO: irq_attach
```
Write USBINTR: USB Interrupt Enable Register

(To enable the USB Interrupts)

USB Interrupt Enable (Bit 0) = 1

USB Error Interrupt Enable (Bit 1) = 1

Port Change Interrupt Enable (Bit 2) = 1

Host System Error Enable (Bit 4) = 1

Interrupt on Async Advance Enable (Bit 5) = 1
```
a64_printreg: 01c1b018<-00000037
a64_ehci_initialize: TODO: up_enable_irq
a64_ehci_initialize: TODO: a64_usbhost_vbusdrive
```
Read PORTSC: Port Status and Control Register (EHCI Page 26)

Port Power (PP, Bit 12) = 1
- Host controller has port power control switches
```
a64_printreg: 01c1b054->00001000
EHCI USB EHCI Initialized
```

The above values look OK for PinePhone.

"ls" crashes when USB Hub Support is enabled

When we enable USB Hub Support and run ls, NuttX halts with an Assertion Failure...

NuttShell (NSH) NuttX-12.0.3
nsh> ls /dev
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: mm_heap/mm_malloc.c:200 task: nsh_main 0x4008b380
up_dump_register: stack = 0x4012e660
up_dump_register: x0:   0x4012e660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f3b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x40a8e218          x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008ecc0          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a95608          x21:  0x400f392d
up_dump_register: x22:  0x0                 x23:  0xc8
up_dump_register: x24:  0x400f1277          x25:  0x40125000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b328        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a97900        
up_dump_register: SP_ELX:    0x40a97610        
up_dump_register: TPIDR_EL0: 0x40a95608        
up_dump_register: TPIDR_EL1: 0x40a95608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff

(Source)

Here's the Assertion Failure: mm/mm_heap/mm_malloc.c

FAR void *mm_malloc(FAR struct mm_heap_s *heap, size_t size) {
  ...
  DEBUGASSERT((next->size & MM_ALLOC_BIT) != 0 &&
              (next->size & MM_PREVFREE_BIT) != 0 &&
              next->preceding == nodesize);

TODO: What does this mean?

TODO: Enable Memory Allocation Log

TODO: Lookup the addresses in the Register Dump

Enumerate USB Devices on PinePhone

How does NuttX enumerate USB Devices?

Let's figure out how NuttX will enumerate the LTE Modem on PinePhone.

At startup, a64_usbhost_initialize creates a thread for...

ehci_waiter, which calls....
a64_wait to wait for a USB Device to be connected...
But a64_wait blocks on a Semaphore pscsem, waiting for a change in the Connection State of a Root Hub Port
pcsem is signalled by a64_connect

TODO: Who calls a64_connect?

Let's assume a64_connect is called by the USB Interrupt Handler a64_ehci_interrupt.

If a64_wait is successful...

ehci_waiter will call...
a64_enumerate, which calls...
usbhost_enumerate, which calls...
usbhost_devdesc to print the USB Descriptor

Let's handle the USB Interrupt, so that a64_connect will be triggered to begin the above USB Enumeration...

Handle USB Interrupt

How will we handle USB Interrupts for NuttX on PinePhone?

Here's the Interrupt Handler for the NuttX USB EHCI Driver...

a64_ehci_interrupt

We need to attach this Interrupt Handler to the USB Interrupt for PinePhone / Allwinner A64 SoC.

What's the USB IRQ for PinePhone?

According to the Allwinner A64 User Manual ("3.12: GIC", Page 212), the IRQ Numbers for USB are...

USB-OTG: 103
USB-OTG-EHCI: 104
USB-OTG-OHCI: 105
USB-EHCI0: 106
USB-OHCI0: 107

We will only handle USB-EHCI0 (IRQ 106), since it's connected to the LTE Modem.

This is how we attach the USB Interrupt Handler a64_ehci_interrupt to IRQ 106...

pinephone-nuttx-usb/a64_ehci.c

Lines 5343 to 5351 in 409a6ed

    
           /* Attach EHCI Interrupt Handler */ 
        
           _info("irq_attach\n");//// 
        
           #define A64_IRQ_USBOTG1 106 //// USB-EHCI0 
        
           ret = irq_attach(A64_IRQ_USBOTG1, a64_ehci_interrupt, NULL); 
        
           /* Set Interrupt Priority in Generic Interrupt Controller v2 */ 
        
           arm64_gic_irq_set_priority(A64_IRQ_USBOTG1, 0, IRQ_TYPE_EDGE);

But the USB Interrupt Handler is not triggered. Let's power on the LTE Modem...

Power On LTE Modem

How to power up PinePhone's LTE Modem?

Read the article...

"NuttX RTOS for PinePhone: 4G LTE Modem"

According to PinePhone Schematic Page 15, the LTE Modem is connected to...

Power DCDC1: From PMIC, 3.3V (See this)
Power VBAT: PL7 (4G-PWR-BAT) (See this)
Power VDD_EXT: From LTE Modem (EG25-G HW Guide Page 22)
Reset: BB-RESET (RESET_N) -> PC4-RESET-4G
Power Key: BB-PWRKEY (PWRKEY) -> PB3-PWRKEY-4G
Disable: BB-DISABLE (W_DISABLE#) -> PH8-DISABLE-4G
Status: PH9-STATUS
Ring Indicator: PMIC ALDO2 1.8V / PL6 (RI) (See this)
AP Ready: BB-AP-READY (AP_READY) -> PH7-AP-READY

Note: RESET_N and PWRKEY are High-Low Inverted when accessed through PinePhone’s GPIO Pins.

(LTE Modem Pins are explained in the next section)

So to power up PinePhone's LTE Modem, we need to...

Program PinePhone's Power Management Integrated Circuit (PMIC) to supply 3.3 V on DCDC1 (Like this)

We skip this because DCDC1 is already powered on.
Set PL7 to High to power on the RF Transceiver and Baseband Processor
Set PC4 to Low to deassert LTE Modem Reset
Set PH7 (AP-READY) to Low to wake up the modem
Set PB2 (DTR) to Low to wake up the modem
Wait 30 milliseconds for VBAT Power Supply to be stable
Toggle PB3 (Power Key) to start the LTE Modem, like this:

Set PB3 to High...

And wait 600 milliseconds...

Then set PB3 to Low.
Set PH8 to High to disable Airplane Mode
Read PH9 to check the LTE Modem Status:

PH9 goes from High to Low when the LTE Modem is ready, in 2.5 seconds.
UART and USB Interfaces will be operational in 13 seconds

The code looks like this: pinephone_bringup.c

// Init PinePhone LTE Modem
int pinephone_modem_init(void)
{
  int ret;

  // Read PH9 to check LTE Modem Status
  #define STATUS (PIO_INPUT | PIO_PORT_PIOH | PIO_PIN9)
  _info("Configure STATUS (PH9) for Input\n");
  ret = a64_pio_config(STATUS);
  DEBUGASSERT(ret == OK);
  _info("Status=%d\n", a64_pio_read(STATUS));

  // Set PL7 to High to Power On LTE Modem (4G-PWR-BAT)

  #define P_OUTPUT (PIO_OUTPUT | PIO_PULL_NONE | PIO_DRIVE_MEDLOW | \
                   PIO_INT_NONE | PIO_OUTPUT_SET)
  #define PWR_BAT (P_OUTPUT | PIO_PORT_PIOL | PIO_PIN7)
  _info("Configure PWR_BAT (PL7) for Output\n");
  ret = a64_pio_config(PWR_BAT);
  DEBUGASSERT(ret >= 0);

  _info("Set PWR_BAT (PL7) to High\n");
  a64_pio_write(PWR_BAT, true);
  _info("Status=%d\n", a64_pio_read(STATUS));

  // Set PC4 to Low to Deassert LTE Modem Reset (BB-RESET / RESET_N)

  #define RESET_N (P_OUTPUT | PIO_PORT_PIOC | PIO_PIN4)
  _info("Configure RESET_N (PC4) for Output\n");
  ret = a64_pio_config(RESET_N);
  DEBUGASSERT(ret >= 0);

  _info("Set RESET_N (PC4) to Low\n");
  a64_pio_write(RESET_N, false);
  _info("Status=%d\n", a64_pio_read(STATUS));

  // Set AP-READY (PH7) to Low to wake up modem

  #define AP_READY (P_OUTPUT | PIO_PORT_PIOH | PIO_PIN7)
  _info("Configure AP-READY (PH7) for Output\n");
  ret = a64_pio_config(AP_READY);
  DEBUGASSERT(ret >= 0);

  _info("Set AP-READY (PH7) to Low to wake up modem\n");
  a64_pio_write(AP_READY, false);
  _info("Status=%d\n", a64_pio_read(STATUS));

  // Set DTR (PB2) to Low to wake up modem

  #define DTR (P_OUTPUT | PIO_PORT_PIOB | PIO_PIN2)
  _info("Configure DTR (PB2) for Output\n");
  ret = a64_pio_config(DTR);
  DEBUGASSERT(ret >= 0);

  _info("Set DTR (PB2) to Low to wake up modem\n");
  a64_pio_write(DTR, false);
  _info("Status=%d\n", a64_pio_read(STATUS));

  _info("Wait 30 ms\n");
  up_mdelay(30);
  _info("Status=%d\n", a64_pio_read(STATUS));

  // Set PB3 to Power On LTE Modem (BB-PWRKEY / PWRKEY).
  // PWRKEY should be pulled down at least 500 ms, then pulled up.

  #define PWRKEY (P_OUTPUT | PIO_PORT_PIOB | PIO_PIN3)
  _info("Configure PWRKEY (PB3) for Output\n");
  ret = a64_pio_config(PWRKEY);
  DEBUGASSERT(ret >= 0);

  _info("Set PWRKEY (PB3) to High\n");
  a64_pio_write(PWRKEY, true);
  _info("Status=%d\n", a64_pio_read(STATUS));

  _info("Wait 600 ms\n");
  up_mdelay(600);
  _info("Status=%d\n", a64_pio_read(STATUS));

  _info("Set PWRKEY (PB3) to Low\n");
  a64_pio_write(PWRKEY, false);
  _info("Status=%d\n", a64_pio_read(STATUS));

  // Set PH8 to High to Enable LTE Modem and Disable Airplane Mode (BB-DISABLE / W_DISABLE#)

  #define W_DISABLE (P_OUTPUT | PIO_PORT_PIOH | PIO_PIN8)
  _info("Configure W_DISABLE (PH8) for Output\n");
  ret = a64_pio_config(W_DISABLE);
  DEBUGASSERT(ret >= 0);

  _info("Set W_DISABLE (PH8) to High\n");
  a64_pio_write(W_DISABLE, true);
  _info("Status=%d\n", a64_pio_read(STATUS));

  // Poll for Modem Status until it becomes Low
  for (int i = 0; i < 30; i++)  // Max 1 minute
    {
      // Read the Modem Status
      uint32_t status = a64_pio_read(STATUS);
      _info("Status=%d\n", status);

      // Stop if Modem Status is Low
      if (status == 0) { break; }

      // Wait 2 seconds
      up_mdelay(2000);
    }

  // TODO: Read PL6 to handle Ring Indicator / [Unsolicited Result Code](https://embeddedfreak.wordpress.com/2008/08/19/handling-urc-unsolicited-result-code-in-hayes-at-command/)

  return OK;
}

References:

PinePhone Power Management
OSDev PinePhone
Genode PinePhone Telephony

LTE Modem Pins

What's the purpose of the above LTE Modem pins?

Read the article...

"NuttX RTOS for PinePhone: 4G LTE Modem"

From Quectel EG25-G Hardware Design Guide...

Power-on/off

Pin Name	Pin No.	I/O	Description	DC Characteristics	Comment
PWRKEY	21	DI	Turn on/off the module	VH = 0.8 V	The output voltage is 0.8V because of the diode drop in the Qualcomm chipset.
RESET_N	20	DI	Reset signal of the module	VIHmax = 2.1 V, VIHmin = 1.3 V, VILmax = 0.5 V	If unused, keep it open.

PWRKEY should be pulled down at least 500 ms, then pulled up

(EG25-G HW Guide, Page 41)
"Make sure that VBAT is stable before pulling down PWRKEY pin. It is recommended that the time between powering up VBAT and pulling down PWRKEY pin is no less than 30 ms."

(EG25-G HW Guide, Page 41)
"The RESET_N pin can be used to reset the module. The module can be reset by driving RESET_N to a low level voltage for 150–460 ms"

(EG25-G HW Guide, Page 42)
Note: RESET_N and PWRKEY are High-Low Inverted when accessed through PinePhone’s GPIO Pins.

Other Interface Pins

Pin Name	Pin No.	I/O	Description	DC Characteristics	Comment
W_DISABLE#	4	DI	Airplane mode control	VILmin = -0.3 V, VILmax = 0.6 V, VIHmin = 1.2 V, VIHmax = 2.0 V	1.8 V power domain. Pull-up by default. At low voltage level, module can enter into airplane mode. If unused, keep it open.
AP_READY	2	DI	Application processor sleep state detection	VILmin = -0.3 V, VILmax = 0.6 V, VIHmin = 1.2 V, VIHmax = 2.0 V	1.8 V power domain. If unused, keep it open.

"The W_DISABLE# pin is pulled up by default. Driving it to low level will let the module enter airplane mode"

(EG25-G HW Guide, Page 37)

USB Interface

Pin Name	Pin No.	I/O	Description	DC Characteristics	Comment
USB_VBUS	71	PI	USB connection detection	Vmax = 5.25 V, Vmin = 3.0 V, Vnorm = 5.0 V, Typical: 5.0 V	If unused, keep it open.

Status Indication

Pin Name	Pin No.	I/O	Description	DC Characteristics	Comment
STATUS	61	OD	Indicate the module operating status.	The drive current should be less than 0.9 mA	An external pull-up resistor is required. If unused, keep it open.

When PWRKEY is pulled Low, STATUS goes High for ≥2.5 s, then STATUS goes Low

(EG25-G HW Guide, Page 41)

Main UART Interface

Pin Name	Pin No.	I/O	Description	DC Characteristics	Comment
RI	62	DO	Ring indicator	VOLmax = 0.45 V, VOHmin = 1.35 V	1.8 V power domain. If unused, keep it open

Power Supply

Pin Name	Pin No.	I/O	Description	DC Characteristics	Comment
VDD_EXT	7	PO	Provide 1.8 V for external circuit	Vnorm = 1.8 V, IOmax = 50 mA	Power supply for external GPIO’s pull up circuits. If unused, keep it open.

I/O Parameters Definition

Type	Description
AI	Analog Input
AO	Analog Output
DI	Digital Input
DO	Digital Output
IO	Bidirectional
OD	Open Drain
PI	Power Input
PO	Power Output

PinePhone Schematic (Page 15)

(TXB0104 is a Voltage Translator)

Test LTE Modem over UART

The LTE Modem to connected to PinePhone (Allwinner A64) at these UART Ports (pic above)...

A64 Port UART3: RX and TX
A64 Port UART4: CTS and RTS
A64 Port PB2: DTR

(Default 115.2 kbps, up to 921.6 kbps)

Thus we may check UART3 to see if the LTE Modem responds to AT Commands.

LTE Modem works OK with UART3 on NuttX yay! See the test log here...

"Test UART with NuttX"

Note: Modem UART flow control is broken

"Not resolved in v1.2 -- assumption is that USB will be used for high-bandwidth modem I/O.

BB-TX and BB-RX are connected to UART3 (PD0/PD1). BB-RTS and BB-CTS are connected to UART4 (PD4/PD5). To use hardware flow control, TX/RX would need to be connected to UART4, swapping PD0/PD1 with the motor control and rear camera reset GPIOs at PD2/PD3. This would need a device tree change.

Hardware flow control can be disabled with the AT+IFC command, and USB can also be used for commands instead of the UART. So the impact of this problem is unclear."

(Source)

Note: Modem PWR_KEY signal resistor population

"Resolved in v1.2 by separating the modem PWRKEY (PB3) and STATUS (PH9) signals.

On the dev phone (1.0) this signal was connected to PB3. This allows for turning on/off the modem via GPIO from a kernel driver. If proper power down is to be implemented in the kernel for the modem, to allow safe shutdown of the modem before turning off the 4g-pwr-bat, kernel has to be able to signal to the modem to shut down and wait 30s. This is not possible on braveheart. Without this signal, kernel can't do anything to shut down the modem, and would have to rely on userspace to properly manage the modem power up/down sequence. Relying on userspace risks users shutting down the modem without proper wait time of 30s, risking modem damage (flash data corruption).

It would be nice to also have access to the STATUS signal from the modem, so that the driver can detect whether the modem is on or off (userspace might have turned modem off already via AT commands). Given that PWR_KEY pulse will either turn the modem on or off, based on the current status, it's necessary to know the current status before sending the pulse.

There's a STATUS signal routed to PWR_KEY on BraveHeart, that keeps the PWRKEY deasserted when the modem is on and it's not possible to pull it up from PB3, even if R1516 would be optionally mounted.

So after powerup you can't change PWR_KEY signal anymore from PB3 even if R1516 is mounted, and it's not possible to turn off the modem via PB3."

(Source)

TODO: Test LTE Modem with USB. Does the USB Enumeration work?

Test CDC ACM over USB

We're now testing USB CDC ACM on PinePhone, to see if NuttX can enumerate USB Devices correctly.

Select these options in menuconfig...

Enable "RTOS Features > Work queue support > Low priority (kernel) worker thread"

Set "Number of low-priority worker threads" to 2
Enable "Device Drivers > USB Host Driver Support > USB Hub Support"

And "CDC/ACM Support"

Does the Quectel LTE Modem run on USB CDC ACM?

The lsusb and dmesg logs for PinePhone might be helpful later...

lsusb log for PinePhone
dmesg log for PinePhone

TODO: Get the USB Config File for PinePhone: /etc/udev/rules.d

Why is "Number of low-priority worker threads" set to 2?

Because "CDC/ACM Support" won't compile with the default value of 1.

Set USB Magnitude / Rate / Threshold

Earlier we saw this code for setting the USB Magnitude, Rate and Threshold in the USB PHY Driver: sun4i_usb_phy_init

static int sun4i_usb_phy_init(struct phy *phy) {
  ...
  // Assume ID is 1 for Port USB 1
  if (usb_phy->id == 0)
    sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN,
      PHY_RES45_CAL_DATA,
      PHY_RES45_CAL_LEN);

  /* Adjust PHY's magnitude and rate */
  sun4i_usb_phy_write(phy, PHY_TX_AMPLITUDE_TUNE,
    PHY_TX_MAGNITUDE | PHY_TX_RATE,
    PHY_TX_AMPLITUDE_LEN);

  /* Disconnect threshold adjustment */
  sun4i_usb_phy_write(phy, PHY_DISCON_TH_SEL,
    data->cfg->disc_thresh, PHY_DISCON_TH_LEN);

(sun4i_usb_phy_write is defined here)

(disc_thresh is 3)

TODO: Is this needed for NuttX?

USB Controller Configuration

Here's the PinePhone USB Controller Configuration in U-Boot Bootloader: phy-sun4i-usb.c

static const struct sun4i_usb_phy_cfg sun50i_a64_cfg = {
  .num_phys = 2,
  .type = sun50i_a64_phy,
  .disc_thresh = 3,
  .phyctl_offset = REG_PHYCTL_A33,
  .dedicated_clocks = true,
  .hci_phy_ctl_clear = PHY_CTL_H3_SIDDQ,
  .phy0_dual_route = true,
};

(PHY_CTL_H3_SIDDQ is 1 << 1)

TODO

USB PHY Power Doc: sun4i-usb-phy.txt
sun4i_usb_phy_power_on

Output Log

DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE:  BL31: v2.2(release):v2.2-904-gf9ea3a629
NOTICE:  BL31: Built : 15:32:12, Apr  9 2020
NOTICE:  BL31: Detected Allwinner A64/H64/R18 SoC (1689)
NOTICE:  BL31: Found U-Boot DTB at 0x4064410, model: PinePhone
NOTICE:  PSCI: System suspend is unavailable


U-Boot 2020.07 (Nov 08 2020 - 00:15:12 +0100)

DRAM:  2 GiB
MMC:   Device 'mmc@1c11000': seq 1 is in use by 'mmc@1c10000'
mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1
Loading Environment from FAT... *** Warning - bad CRC, using default environment

starting USB...
No working controllers found
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
653 bytes read in 3 ms (211.9 KiB/s)
## Executing script at 4fc00000
gpio: pin 114 (gpio 114) value is 1
359853 bytes read in 21 ms (16.3 MiB/s)
Uncompressed size: 10539008 = 0xA0D000
36162 bytes read in 5 ms (6.9 MiB/s)
1078500 bytes read in 51 ms (20.2 MiB/s)
## Flattened Device Tree blob at 4fa00000
   Booting using the fdt blob at 0x4fa00000
   Loading Ramdisk to 49ef8000, end 49fff4e4 ... OK
   Loading Device Tree to 0000000049eec000, end 0000000049ef7d41 ... OK

Starting kernel ...

pinephone_pmic_init: Set DLDO1 Voltage to 3.3V
pmic_write: reg=0x15, val=0x1a
a64_rsb_write: rt_addr=0x2d, reg_addr=0x15, value=0x1a
pmic_clrsetbits: reg=0x12, clr_mask=0x0, set_mask=0x8
a64_rsb_read: rt_addr=0x2d, reg_addr=0x12
a64_rsb_write: rt_addr=0x2d, reg_addr=0x12, value=0xd9
pinephone_pmic_init: Set LDO Voltage to 3.3V
pmic_write: reg=0x91, val=0x1a
a64_rsb_write: rt_addr=0x2d, reg_addr=0x91, value=0x1a
pinephone_pmic_init: Enable LDO mode on GPIO0
pmic_write: reg=0x90, val=0x3
a64_rsb_write: rt_addr=0x2d, reg_addr=0x90, value=0x3
pinephone_pmic_init: Set DLDO2 Voltage to 1.8V
pmic_write: reg=0x16, val=0xb
a64_rsb_write: rt_addr=0x2d, reg_addr=0x16, value=0xb
pmic_clrsetbits: reg=0x12, clr_mask=0x0, set_mask=0x10
a64_rsb_read: rt_addr=0x2d, reg_addr=0x12
a64_rsb_write: rt_addr=0x2d, reg_addr=0x12, value=0xd9
a64_usbhost_clk_enable: CLK_USB_PHY0
set_bit: 0x1c200cc Bit 8
a64_usbhost_clk_enable: CLK_USB_PHY1
set_bit: 0x1c200cc Bit 9
a64_usbhost_clk_enable: CLK_BUS_OHCI0
set_bit: 0x1c20060 Bit 28
a64_usbhost_clk_enable: CLK_BUS_EHCI0
set_bit: 0x1c20060 Bit 24
a64_usbhost_clk_enable: CLK_USB_OHCI0
set_bit: 0x1c200cc Bit 16
a64_usbhost_clk_enable: CLK_BUS_OHCI1
set_bit: 0x1c20060 Bit 29
a64_usbhost_clk_enable: CLK_BUS_EHCI1
set_bit: 0x1c20060 Bit 25
a64_usbhost_clk_enable: CLK_USB_OHCI1
set_bit: 0x1c200cc Bit 17
a64_usbhost_reset_deassert: RST_USB_PHY0
set_bit: 0x1c200cc Bit 0
a64_usbhost_reset_deassert: RST_USB_PHY1
set_bit: 0x1c200cc Bit 1
a64_usbhost_reset_deassert: RST_BUS_OHCI0
set_bit: 0x1c202c0 Bit 28
a64_usbhost_reset_deassert: RST_BUS_EHCI0
set_bit: 0x1c202c0 Bit 24
a64_usbhost_reset_deassert: RST_BUS_OHCI1
set_bit: 0x1c202c0 Bit 29
a64_usbhost_reset_deassert: RST_BUS_EHCI1
set_bit: 0x1c202c0 Bit 25
a64_usbhost_initialize: TODO: switch off USB bus power
a64_usbhost_initialize: TODO: Setup pins, with power initially off
usbhost_registerclass: Registering class:0x40125838 nids:2
EHCI Initializing EHCI Stack
a64_printreg: 01c1b010<-00000000
a64_printreg: 01c1b014->00001000
a64_printreg: 01c1b010->00000000
a64_printreg: 01c1b010<-00000002
a64_printreg: 01c1b010->00080b00
a64_printreg: 01c1b018<-00000000
a64_printreg: 01c1b014<-0000003f
EHCI HCIVERSION 1.00
a64_printreg: 01c1b004->00001101
EHCI nports=1, HCSPARAMS=1101
a64_printreg: 01c1b008->0000a026
EHCI HCCPARAMS=00a026
a64_printreg: 01c1b028<-40a88fa0
a64_printreg: 01c1b024<-40a99000
a64_printreg: 01c1b010->00080b00
a64_printreg: 01c1b010<-00080b30
a64_printreg: 01c1b010->00080b30
a64_printreg: 01c1b010<-00080b31
a64_printreg: 01c1b050->00000000
a64_printreg: 01c1b050<-00000001
a64_printreg: 01c1b014->00000000
a64_ehci_initialize: irq_attach
a64_printreg: 01c1b018<-00000037
a64_ehci_initialize: up_enable_irq
a64_ehci_initialize: TODO: a64_usbhost_vbusdrive
a64_printreg: 01c1b054->00001000
EHCI USB EHCI Initialized
a64_usbhost_initialize: 1
a64_usbhost_initialize: Status=0
pinephone_pmic_usb_init: Set DCDC1 Voltage to 3.3V
pmic_write: reg=0x20, val=0x11
a64_rsb_write: rt_addr=0x2d, reg_addr=0x20, value=0x11
pmic_clrsetbits: reg=0x10, clr_mask=0x0, set_mask=0x1
a64_rsb_read: rt_addr=0x2d, reg_addr=0x10
a64_rsb_write: rt_addr=0x2d, reg_addr=0x10, value=0x37
a64_usbhost_initialize: Status=0
a64_usbhost_initialize: Wait 1000 ms
a64_usbhost_initialize: Status=0
a64_usbhost_initialize: Configure PWR_BAT (PL7) for Output
a64_usbhost_initialize: Set PWR_BAT (PL7) to High
a64_usbhost_initialize: Status=1
a64_usbhost_initialize: Wait 1000 ms
a64_usbhost_initialize: Status=1
a64_usbhost_initialize: Configure RESET_N (PC4) for Output
a64_usbhost_initialize: Set RESET_N (PC4) to High
a64_usbhost_initialize: Status=1
a64_usbhost_initialize: Configure PWRKEY (PB3) for Output
a64_usbhost_initialize: Set PWRKEY (PB3) to High
a64_usbhost_initialize: Status=1
a64_usbhost_initialize: Wait 30 ms for VBAT to be stable
a64_usbhost_initialize: Status=1
a64_usbhost_initialize: Set PWRKEY (PB3) to Low
a64_usbhost_initialize: Status=1
a64_usbhost_initialize: Wait 500 ms
a64_usbhost_initialize: Status=1
a64_usbhost_initialize: Set PWRKEY (PB3) to High
a64_usbhost_initialize: Status=1
a64_usbhost_initialize: Configure W_DISABLE (PH8) for Output
a64_usbhost_initialize: Set W_DISABLE (PH8) to High
a64_usbhost_initialize: Status=1
a64_usbhost_initialize: Green LED
a64_usbhost_initialize: Status=1
a64_usbhost_initialize: Red LED
a64_usbhost_initialize: Status=1
a64_usbhost_initialize: Blue LED
a64_usbhost_initialize: Status=1
nsh: mkfatfs: command not found

e
h
cNuttShell (NSH) NuttX-12.0.3
i
_nsh>waiter: ehci_waiter:  Running
a64_wait: Wait for connect / disconnect
 
nsh> ls
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: mm_heap/mm_malloc.c:200 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x40a8d218          x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc8
up_dump_register: x24:  0x400f0277          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a96610        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a96550        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a96490        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a963d0        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a96310        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a96250        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a96190        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a960d0        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a96010        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a95f50        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a95e90        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a95dd0        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a95d10        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a95c50        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a95b90        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a95ad0        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a95a10        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a95950        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a95890        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a957d0        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a95710        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a95650        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a95590        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a954d0        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a95410        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a95350        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a95290        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a951d0        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a95110        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
_assert: Current Version: NuttX  12.0.3 4d922be-dirty Mar  7 2023 15:54:47 arm64
_assert: Assertion failed : at file: misc/lib_mutex.c:194 task: nsh_main 0x4008b230
up_dump_register: stack = 0x4012d660
up_dump_register: x0:   0x4012d660          x1:   0xa
up_dump_register: x2:   0x20                x3:   0x400f2b22
up_dump_register: x4:   0x4a10              x5:   0x0
up_dump_register: x6:   0x4                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x0
up_dump_register: x20:  0x40a94608          x21:  0x400f292d
up_dump_register: x22:  0x0                 x23:  0xc2
up_dump_register: x24:  0x400effd8          x25:  0x40124000
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008b1d8        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x40000005        
up_dump_register: ELR:       0x40081000        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a95050        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0xffffffffffffffff
up_dump_register: stack = 0x40a94f90
up_dump_register: x0:   0x66                x1:   0xffffffff
up_dump_register: x2:   0x0                 x3:   0x400f2b22
up_dump_register: x4:   0x4                 x5:   0xfffffffffffffffc
up_dump_register: x6:   0xf                 x7:   0x88
up_dump_register: x8:   0x888               x9:   0x0
up_dump_register: x10:  0x2                 x11:  0xa200023
up_dump_register: x12:  0x1c                x13:  0x1
up_dump_register: x14:  0x0                 x15:  0x1c28000
up_dump_register: x16:  0x4008eb70          x17:  0x1
up_dump_register: x18:  0x0                 x19:  0x40a94848
up_dump_register: x20:  0x40a948c8          x21:  0x66
up_dump_register: x22:  0x0                 x23:  0x40a968a8
up_dump_register: x24:  0x400f15a7          x25:  0x400f0957
up_dump_register: x26:  0x0                 x27:  0x0
up_dump_register: x28:  0x0                 x29:  0x0
up_dump_register: x30:  0x4008904c        
up_dump_register: 
up_dump_register: STATUS Registers:
up_dump_register: SPSR:      0x60000005        
up_dump_register: ELR:       0x4008907c        
up_dump_register: SP_EL0:    0x40a96900        
up_dump_register: SP_ELX:    0x40a94f90        
up_dump_register: TPIDR_EL0: 0x40a94608        
up_dump_register: TPIDR_EL1: 0x40a94608        
up_dump_register: EXE_DEPTH: 0x0

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

README.md

README.md

PinePhone USB Driver for Apache NuttX RTOS

64-Bit Update for EHCI Driver

Halt Timeout for USB Controller

PinePhone USB Drivers in U-Boot Bootloader

USB Enhanced Host Controller Interface vs On-The-Go

Power On the USB Controller

USB Controller Clocks

USB Controller Reset

Enable USB Controller Clocks

Reset USB Controller

NuttX EHCI Driver Starts OK on PinePhone

Decode EHCI Register Values

"ls" crashes when USB Hub Support is enabled

Enumerate USB Devices on PinePhone

Handle USB Interrupt

Power On LTE Modem

LTE Modem Pins

Test LTE Modem over UART

Test CDC ACM over USB

Set USB Magnitude / Rate / Threshold

USB Controller Configuration

TODO

Output Log

	/* Internal representation of the EHCI Queue Head (QH) */

	struct a64_epinfo_s;
	struct a64_qh_s
	{
	/* Fields visible to hardware */

	struct ehci_qh_s hw; /* Hardware representation of the queue head */

	/* Internal fields used by the EHCI driver */

	struct a64_epinfo_s epinfo; / Endpoint used for the transfer */
	uint32_t fqp; /* First qTD in the list (physical address) */
	uint8_t pad[8]; /* Padding to assure 32-byte alignment */
	};

	DEBUGASSERT(sizeof(struct ehci_itd_s) == SIZEOF_EHCI_ITD_S);////
	DEBUGASSERT(sizeof(struct ehci_sitd_s) == SIZEOF_EHCI_SITD_S);////
	DEBUGASSERT(sizeof(struct ehci_qtd_s) == SIZEOF_EHCI_QTD_S);////
	DEBUGASSERT(sizeof(struct ehci_overlay_s) == 32);////
	DEBUGASSERT(sizeof(struct ehci_qh_s) == 48);////
	DEBUGASSERT(sizeof(struct ehci_fstn_s) == SIZEOF_EHCI_FSTN_S);////

	/****************************************************************************
	* Name: a64_reset
	*
	* Description:
	* Set the HCRESET bit in the USBCMD register to reset the EHCI hardware.
	*
	* Table 2-9. USBCMD - USB Command Register Bit Definitions
	*
	* "Host Controller Reset (HCRESET) ... This control bit is used by
	* software to reset the host controller. The effects of this on Root
	* Hub registers are similar to a Chip Hardware Reset.
	*
	* "When software writes a one to this bit, the Host Controller resets its
	* internal pipelines, timers, counters, state machines, etc. to their
	* initial value. Any transaction currently in progress on USB is
	* immediately terminated. A USB reset is not driven on downstream
	* ports.
	*
	* "PCI Configuration registers are not affected by this reset. All
	* operational registers, including port registers and port state
	* machines are set to their initial values. Port ownership reverts
	* to the companion host controller(s)... Software must reinitialize
	* the host controller ... in order to return the host controller to
	* an operational state.
	*
	* "This bit is set to zero by the Host Controller when the reset process
	* is complete. Software cannot terminate the reset process early by
	* writing a zero to this register. Software should not set this bit to
	* a one when the HCHalted bit in the USBSTS register is a zero.
	* Attempting to reset an actively running host controller will result
	* in undefined behavior."
	*
	* Input Parameters:
	* None.
	*
	* Returned Value:
	* Zero (OK) is returned on success; A negated errno value is returned
	* on failure.
	*
	* Assumptions:
	* - Called during the initialization of the EHCI.
	*
	****************************************************************************/

	static int a64_reset(void)
	{
	uint32_t regval;
	unsigned int timeout;

	/* Make sure that the EHCI is halted: "When [the Run/Stop] bit is set to
	* 0, the Host Controller completes the current transaction on the USB and
	* then halts. The HC Halted bit in the status register indicates when the
	* Host Controller has finished the transaction and has entered the
	* stopped state..."
	*/

	a64_putreg(0, &HCOR->usbcmd);

	/* "... Software should not set [HCRESET] to a one when the HCHalted bit in
	* the USBSTS register is a zero. Attempting to reset an actively running
	* host controller will result in undefined behavior."
	*/

	timeout = 0;
	do
	{
	/* Wait one microsecond and update the timeout counter */

	up_udelay(1);
	timeout++;

	/* Get the current value of the USBSTS register. This loop will
	* terminate when either the timeout exceeds one millisecond or when
	* the HCHalted bit is no longer set in the USBSTS register.
	*/

	regval = a64_getreg(&HCOR->usbsts);
	}
	while (((regval & EHCI_USBSTS_HALTED) == 0) && (timeout < 1000));

	/* Is the EHCI still running? Did we timeout? */

	if ((regval & EHCI_USBSTS_HALTED) == 0)
	{
	usbhost_trace1(EHCI_TRACE1_HCHALTED_TIMEOUT, regval);
	return -ETIMEDOUT;
	}

	#define A64_CCU_ADDR 0x01c20000 /* CCU 0x01c2:0000-0x01c2:03ff 1K */

	/* Display Engine Clock Register (A64 Page 117) */
	// #define DE_CLK_REG (A64_CCU_ADDR + 0x0104)
	// #define CLK_SRC_SEL(n) ((n) << 24)
	// #define CLK_SRC_SEL_MASK (0b111 << 24)
	// #define SCLK_GATING (1 << 31)
	// #define SCLK_GATING_MASK (0b1 << 31)

	/* Bus Software Reset Register 1 (A64 Page 140) */
	// #define BUS_SOFT_RST_REG1 (A64_CCU_ADDR + 0x02c4)
	// #define DE_RST (1 << 12)

	// Set the bit
	static void set_bit(unsigned long addr, uint8_t bit)
	{
	_info("0x%lx Bit %d\n", addr, bit);
	modreg32(1 << bit, 1 << bit, addr);
	}

	// Enable USB Clocks
	// https://github.com/lupyuen/pinephone-nuttx-usb#usb-controller-clocks
	// https://github.com/lupyuen/pinephone-nuttx-usb#enable-usb-controller-clocks
	static void a64_usbhost_clk_enable(void)
	{
	// usb0_phy: CLK_USB_PHY0
	// 0x0cc BIT(8)
	_info("CLK_USB_PHY0\n");
	#define CLK_USB_PHY0 (A64_CCU_ADDR + 0x0cc)
	#define CLK_USB_PHY0_BIT 8
	set_bit(CLK_USB_PHY0, CLK_USB_PHY0_BIT);

	// usb1_phy: CLK_USB_PHY1
	// 0x0cc BIT(9)
	_info("CLK_USB_PHY1\n");
	#define CLK_USB_PHY1 (A64_CCU_ADDR + 0x0cc)
	#define CLK_USB_PHY1_BIT 9
	set_bit(CLK_USB_PHY1, CLK_USB_PHY1_BIT);

	// EHCI0: CLK_BUS_OHCI0, CLK_BUS_EHCI0, CLK_USB_OHCI0
	// 0x060 BIT(28)
	_info("CLK_BUS_OHCI0\n");
	#define CLK_BUS_OHCI0 (A64_CCU_ADDR + 0x060)
	#define CLK_BUS_OHCI0_BIT 28
	set_bit(CLK_BUS_OHCI0, CLK_BUS_OHCI0_BIT);

	// 0x060 BIT(24)
	_info("CLK_BUS_EHCI0\n");
	#define CLK_BUS_EHCI0 (A64_CCU_ADDR + 0x060)
	#define CLK_BUS_EHCI0_BIT 24
	set_bit(CLK_BUS_EHCI0, CLK_BUS_EHCI0_BIT);

	// 0x0cc BIT(16)
	_info("CLK_USB_OHCI0\n");
	#define CLK_USB_OHCI0 (A64_CCU_ADDR + 0x0cc)
	#define CLK_USB_OHCI0_BIT 16
	set_bit(CLK_USB_OHCI0, CLK_USB_OHCI0_BIT);

	// EHCI1: CLK_BUS_OHCI1, CLK_BUS_EHCI1, CLK_USB_OHCI1
	// 0x060 BIT(29)
	_info("CLK_BUS_OHCI1\n");
	#define CLK_BUS_OHCI1 (A64_CCU_ADDR + 0x060)
	#define CLK_BUS_OHCI1_BIT 29
	set_bit(CLK_BUS_OHCI1, CLK_BUS_OHCI1_BIT);

	// 0x060 BIT(25)
	_info("CLK_BUS_EHCI1\n");
	#define CLK_BUS_EHCI1 (A64_CCU_ADDR + 0x060)
	#define CLK_BUS_EHCI1_BIT 25
	set_bit(CLK_BUS_EHCI1, CLK_BUS_EHCI1_BIT);

	// 0x0cc BIT(17)
	_info("CLK_USB_OHCI1\n");
	#define CLK_USB_OHCI1 (A64_CCU_ADDR + 0x0cc)
	#define CLK_USB_OHCI1_BIT 17
	set_bit(CLK_USB_OHCI1, CLK_USB_OHCI1_BIT);

	/* Display Engine Clock Register (A64 Page 117)
	* Set SCLK_GATING (Bit 31) to 1
	* (Enable Special Clock)
	* Set CLK_SRC_SEL (Bits 24 to 26) to 1
	* (Clock Source is Display Engine PLL)
	*/
	// clk = SCLK_GATING \| CLK_SRC_SEL(1);
	// clk_mask = SCLK_GATING_MASK \| CLK_SRC_SEL_MASK;
	// modreg32(clk, clk_mask, DE_CLK_REG);
	}

	// Deassert USB Resets
	// https://github.com/lupyuen/pinephone-nuttx-usb#usb-controller-reset
	// https://github.com/lupyuen/pinephone-nuttx-usb#reset-usb-controller
	static void a64_usbhost_reset_deassert(void)
	{
	// usb0_reset: RST_USB_PHY0
	// 0x0cc BIT(0)
	_info("RST_USB_PHY0\n");
	#define RST_USB_PHY0 (A64_CCU_ADDR + 0x0cc)
	#define RST_USB_PHY0_BIT 0
	set_bit(RST_USB_PHY0, RST_USB_PHY0_BIT);

	// usb1_reset: RST_USB_PHY1
	// 0x0cc BIT(1)
	_info("RST_USB_PHY1\n");
	#define RST_USB_PHY1 (A64_CCU_ADDR + 0x0cc)
	#define RST_USB_PHY1_BIT 1
	set_bit(RST_USB_PHY1, RST_USB_PHY1_BIT);

	// EHCI0: RST_BUS_OHCI0, RST_BUS_EHCI0
	// 0x2c0 BIT(28)
	_info("RST_BUS_OHCI0\n");
	#define RST_BUS_OHCI0 (A64_CCU_ADDR + 0x2c0)
	#define RST_BUS_OHCI0_BIT 28
	set_bit(RST_BUS_OHCI0, RST_BUS_OHCI0_BIT);

	// 0x2c0 BIT(24)
	_info("RST_BUS_EHCI0\n");
	#define RST_BUS_EHCI0 (A64_CCU_ADDR + 0x2c0)
	#define RST_BUS_EHCI0_BIT 24
	set_bit(RST_BUS_EHCI0, RST_BUS_EHCI0_BIT);

	// EHCI1: RST_BUS_OHCI1, RST_BUS_EHCI1
	// 0x2c0 BIT(29)
	_info("RST_BUS_OHCI1\n");
	#define RST_BUS_OHCI1 (A64_CCU_ADDR + 0x2c0)
	#define RST_BUS_OHCI1_BIT 29
	set_bit(RST_BUS_OHCI1, RST_BUS_OHCI1_BIT);

	// 0x2c0 BIT(25)
	_info("RST_BUS_EHCI1\n");
	#define RST_BUS_EHCI1 (A64_CCU_ADDR + 0x2c0)
	#define RST_BUS_EHCI1_BIT 25
	set_bit(RST_BUS_EHCI1, RST_BUS_EHCI1_BIT);

	/* Bus Software Reset Register 1 (A64 Page 140)
	* Set DE_RST (Bit 12) to 1 (De-Assert Display Engine)
	*/
	// modreg32(DE_RST, DE_RST, BUS_SOFT_RST_REG1);
	}

	/****************************************************************************
	* Public Functions
	****************************************************************************/

	/****************************************************************************
	* Name: a64_usbhost_initialize
	*
	* Description:
	* Called at application startup time to initialize the USB host
	* functionality.
	* This function will start a thread that will monitor for device
	* connection/disconnection events.
	*
	****************************************************************************/

	int a64_usbhost_initialize(void)
	{
	int ret;

	a64_usbhost_clk_enable();

	a64_usbhost_reset_deassert();

	/* Attach EHCI Interrupt Handler */

	_info("irq_attach\n");////
	#define A64_IRQ_USBOTG1 106 //// USB-EHCI0
	ret = irq_attach(A64_IRQ_USBOTG1, a64_ehci_interrupt, NULL);

	/* Set Interrupt Priority in Generic Interrupt Controller v2 */

	arm64_gic_irq_set_priority(A64_IRQ_USBOTG1, 0, IRQ_TYPE_EDGE);

Files

README.md

Latest commit

History

README.md

File metadata and controls

PinePhone USB Driver for Apache NuttX RTOS

64-Bit Update for EHCI Driver

Halt Timeout for USB Controller

PinePhone USB Drivers in U-Boot Bootloader

USB Enhanced Host Controller Interface vs On-The-Go

Power On the USB Controller

USB Controller Clocks

USB Controller Reset

Enable USB Controller Clocks

Reset USB Controller

NuttX EHCI Driver Starts OK on PinePhone

Decode EHCI Register Values

"ls" crashes when USB Hub Support is enabled

Enumerate USB Devices on PinePhone

Handle USB Interrupt

Power On LTE Modem

LTE Modem Pins

Test LTE Modem over UART

Test CDC ACM over USB

Set USB Magnitude / Rate / Threshold

USB Controller Configuration

TODO

Output Log