User Manual for the THC Isolated ADC available now. #6
Replies: 4 comments 6 replies
-
|
Hello, |
Beta Was this translation helpful? Give feedback.
-
|
Yes, I have a couple. $20. And yes, I still have the breakout boards. I can ship together, no extra charge. Make a note in the tindie purchase (special instructions) - say ADC and Toutoune86 so I can connect the order to your post here. You can pay the $20 via paypal separately from the tindie transaction (I haven't put it as a tinde product yet). I will send instructions after the tindie order. Should not take much extra time but ping me here as well - tindie has been recently having some email notification problems. Phil |
Beta Was this translation helpful? Give feedback.
-
|
Hi Phil, Thanks, Dana |
Beta Was this translation helpful? Give feedback.
-
|
Yes, I just got a small run of the final version in. I've had a lot of work to do lately but will be putting the ADC boards up on Tindie. They will be priced at $29.99 USD through Tindie. (The ADC chip is annoyingly expensive for what it does.) I still have a number of things left to get the board up on Tindie so I'll sell direct to you for $20 USD. US Shipping is$5.50, contact me if non-US shipping. If you order a T41U5XBB on Tindie, I will ship them together and save you the postage. You will need to contact me on Tindie if you want to do that so I can give you payment instructions for the ADC. Phil |
Beta Was this translation helpful? Give feedback.
-
|
Ok, thanks for the informations.
I live in France, could you ship the boards here ? How much would it be for
the shipment ?
I hope it would not be too much a pain to send abroad.
Best regards,
Tristan Cousin.
|
Beta Was this translation helpful? Give feedback.
-
|
The shipping costs are shown on the tindie site. Shipping to France is a little less than $20 USD. No additional shipping cost for the ADC. I ship internationally so it is very easy for me. |
Beta Was this translation helpful? Give feedback.
-
|
Hello again
and Happy new year !
I have spent some times reading your manual and some of you blog posts to
understand better the process of assembling your T41U5XBB, loading its
Teensy with the apropriate firmware, and running it. The aim is to foresee
some possible issues or incompatibility between your device on one side and
my needs and situation. I guess you do not earn a lot from each sale
compared to what I would have to pay, considering your expenses, shipping
fees, TAV, etc. I will therefore try to be as short as possible in my
questions and thank you warmly for whatever replies you may take the time
to give me. These are the questions the answers of which I was not able to
reply or understand fully through your documentation and my knowledge.
My situtation is this one:
I plan to use my CNC mainly for plasma cutting, with 3 cartesian axis and
a 4th rotary axis. I currently still have some EMI issues remaining in
spite of various shielding and grounding tasks. I expect especially your
electronic design to relieve this problem. I guess therefore the ethernet
version is better than the USB version, I think USB cable was the cause of
most o y issues (And yes, I fully agree, EMI is so invisible and
mysterious, it often looks like vaudoo, I used to call it shamanic until I
read you)
I have no Internet connection in my workshop, therfore no router yet. I
just have one motor and driver for my Y axis, on which my X axis is in
hangover. It may be sufficient for a plasma use, not for possible addons
like a routing spindle. So I may later install a 2nd mirrored Y motor and
hence need a 5th axis control, should I want to make X an Y square.
My main questions are about the ehternet feature cable :
- In the manual (page4) you say there may be two versions one with
ethernet, another one with USB, which is not the case yet. I would like to
be sure manual is up to date and the breakoutboard is ethernet compatible,
even though it is called on Tindie a "t41*U*xbb".
- It may look like a stupid question, but I wonder if the connection
with the router or ethernet switch would work even whitout internet
connection.
- Also, I fear the the router or switch, or even the use of an extra
ethernet cable between the router and the computer may be as well another
exposure to IME and corrupt the connection. May be the TCP/IP protocol
itself prevents from such risk ? I would be glad to have your feedback
regarding the experiences you had or heard about regarding this
configuration
- I was considering as well to use a single and direct ethernet
connection to my PC (pages 14 and 15), even though you say it may be more
complex. But I just have one network interface connector in my PC. So I
should in this case use an USB adpapter, which is pretty sensitive to EMI,
I guess, no ? I have not understood if this aditionnal connector was just
plugged for a temporary use, ie to set the IP address, gateway and mask,
or whether it would have to remain and therefore pose a remainng EMI
vulnerability risk.
- I did not undertsand your advice page 14 "2. Secure a cross-over
Ethernet cable. It may be unnecessary but it won't hurt." Does it mean we
may rather need a straight cable and can not know it yet until trying ?
does "secure" mean we may ned to have one axtra available ?
- If the the Ethernet may not work properly due to EMI with T41U5XBB, do
you think the Pico's wifi may be a relevant, noise-proof solution ?
My last questions regard the THC plugin. I am just autodidact and in no way
engineer in electronics and do not understand the I2C plugging.
- How does it work ? I see on the THC board that tere are the same pins
than those dedicated to I2C on the breakout board ( Halt, +V, St, Sd Sc,
Ground). Is it enough, as for hardware connection achivement, to connect
each end of 6 wires to the pin of the same name in each board ? (then I
would recommend to add it to the manual, i may not be so obvious for other
people too)
- And what does ADC mean in this case ? Analog/Digital Converter?
I thank you both for your work in general and for your replies. I am
looking forward to finish my plasma CNC, and would be glad later if I can,
to give some THC plugin feedbacks.
Best regards,
Le sam. 16 déc. 2023 à 18:23, phil-barrett ***@***.***> a
écrit :
… The shipping costs are shown on the tindie site
<https://www.tindie.com/products/philba/grblhal-bob-unkit-for-teensy-41-t41u5xbb/>.
Shipping to France is a little less than $20 USD. No additional shipping
cost for the ADC.
—
Reply to this email directly, view it on GitHub
<#6 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AGQ464FQ7YWUSM2XQT6NQEDYJXKIJAVCNFSM6AAAAAA7D3MRRGVHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM3TQNZSGA2TA>
.
You are receiving this because you are subscribed to this thread.Message
ID: ***@***.***>
--
Tristan Cousin
06 45 17 14 03
https://tricyclos.wordpress.com : Mécanique vélo, vélo-cargo et motorisation
|
Beta Was this translation helpful? Give feedback.
-
|
I'm running out sorry for the terse replies. I will be happy to elucidate further. ADC = analog to digital |
Beta Was this translation helpful? Give feedback.
-
|
Looks like I’m going to get the ADC only for now. I wasn’t sure my board had the required connection to work, but I’ve since verified I have the i2C. My shipping info is: Dana Smith 11190 Bonham Ranch Rd Dripping Springs, TX 78620. How and where would you like me to pay ? I think I’d like to buy 2 ADCs. With shippingThanks again!DanaSent from my iPhoneOn Oct 16, 2024, at 2:20 PM, phil-barrett ***@***.***> wrote:
Yes, I just got a small run of the final version in. I've had a lot of work to do lately but will be putting the ADC boards up on Tindie. They will be priced at $29.99 USD through Tindie. (The ADC chip is annoyingly expensive for what it does.) I still have a number of things left to get the board up on Tindie so I'll sell direct to you for $20 USD. US Shipping is$5.50, contact me if non-US shipping. If you order a T41U5XBB on Tindie, I will ship them together and save you the postage. You will need to contact me on Tindie if you want to do that so I can give you payment instructions for the ADC.
Phil
—Reply to this email directly, view it on GitHub, or unsubscribe.You are receiving this because you commented.Message ID: ***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
|
Either put your email address here or connect to me via the Tindie page for the Teensy board. I don't want to put my email address on github and don't recommend others do that but it's your choice (wish they had a secure messaging option). |
Beta Was this translation helpful? Give feedback.
-
V1.0 of the THC Isolated ADC manual is now available.
Feedback, suggestions or corrections are greatly appreciated. Either here or on the THC Isolated ADC github page.
Also, I still have a few boards available.
Beta Was this translation helpful? Give feedback.
All reactions