Klipper Config

• Sidewinder X1
• BLTouch/CRTouch on Z-min
• Filament on Z-max
• MKS Mini12864 V3

Firmware Build

cd ~/klipper/
make menuconfig

Seems to be defaults:

• Atmega AVR
• atmega2560
• 16Mhz
• 250000 baud
• Enable GPIO at startup for hotend fans
  • AR9,AR7

make clean
make

Flashing

ls /dev/serial/by-id/*
> /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
sudo service klipper stop
make flash FLASH_DEVICE=/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
sudo service klipper start

Configuration

https://www.klipper3d.org/Config_Reference.html https://github.com/tispokes/klipper_on_SWX1 https://docs.arduino.cc/hacking/hardware/PinMapping2560 https://www.klipper3d.org/Config_checks.html

Hardware

Acceleration: 3000 might have been high

Vref = I x 8 x R 1.02 = I x 8 x 0.08

1.02 = 1.3 x 8 x 0.1

Vref 1.02V = 1.6 A

E = 1A = 0.64 Vref X,Z = 1.7A = 1.088 Vref Y = 1.7A = 1.088 Vref

XYZ = 1A = 0.68 Vref E = 1.4A = 0.9 Vref

Random internet person found same default:

Stock is Set XYZ = 1.0V E = 1.0V , I dialed my 2208's down a bit. I like to run XYZ = 0.68V E= 0.9V anywhere in this ange is perfectly fine just don't' exceed 1.0V

Tuning

Filament rotation distance

70 - 17.66 = 52.34 7 * 52.34 / 50 = 7.328

Mainsail Config

https://docs.mainsail.xyz/overview/quicktips/slicer-upload

Leveling

https://github.com/kyleisah/Klipper-Adaptive-Meshing-Purging

Prusa Slicer Config

• Start Gcode

SET_PRINT_STATS_INFO TOTAL_LAYER=[total_layer_count]
START_PRINT

• End Gcode

END_PRINT

• After layer change

;AFTER_LAYER_CHANGE
;[layer_z]

SET_PRINT_STATS_INFO CURRENT_LAYER={layer_num + 1}

Revised Setup Instructions...

A mix of configs, trying to use github to manage all via moonraker conf

# Setup repo folders:
mkdir ~/custom/
cd custom
git clone https://github.com/kyleisah/Klipper-Adaptive-Meshing-Purging.git
ln -s ~/custom/Klipper-Adaptive-Meshing-Purging/Configuration/ ~/printer_data/config/KAMP
git clone https://github.com/cbo100/KlipperConfig.git
ln -s ~/custom/KlipperConfig/ ~/printer_data/config/SidewinderX1

Replace printer.cfg:

[include mainsail.cfg]
[include timelapse.cfg]
[include ./SidewinderX1/SidewinderX1.cfg]

[virtual_sdcard]
path: ~/printer_data/gcodes

Add to moonraker.conf:

[update_manager Klipper-Adaptive-Meshing-Purging]
type: git_repo
channel: dev
path: ~/custom/Klipper-Adaptive-Meshing-Purging
origin: https://github.com/kyleisah/Klipper-Adaptive-Meshing-Purging.git
managed_services: klipper
primary_branch: main

[update_manager SidewinderX1-Config]
type: git_repo
channel: dev
path: ~/custom/KlipperConfig
origin: https://github.com/cbo100/KlipperConfig
managed_services: klipper
primary_branch: main