Hiking DDS238-2 Wifi meter MQTT reports

[Stormhand]

Hello,
I have this meter flashed with Tasmota 12.2.0 where the Rule1 is to execute TuyaSend8 every 5 seconds. However it sends MQTT results every 1 minute and i cannot find how to shorten it to "every 10s". Here is the log:

6:52:08.395 RUL: RULES#TIMER=1 performs "backlog TuyaSend8; RuleTimer1 5"
06:52:08.444 MQT: stat/home/tasmota_dds238_2/RESULT = {"TuyaSend":"Done"}
06:52:08.514 TYA: MCU Product ID: {"p":"sw9asyjj8j44frjl","v":"1.0.0","m":0}
06:52:08.639 MQT: stat/home/tasmota_dds238_2/RESULT = {"T1":5,"T2":0,"T3":0,"T4":0,"T5":0,"T6":0,"T7":0,"T8":0}
06:52:09.410 MQT: tele/home/tasmota_dds238_2/STATE = {"Time":"2024-12-18T06:52:09+00:00","Uptime":"5T07:11:36","UptimeSec":457896,"Heap":25,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":40,"POWER":"ON","Wifi":{"AP":1,"SSId":"home","BSSId":"2E:61:F1:8A:A1:20","Channel":2,"Mode":"11n","RSSI":34,"Signal":-83,"LinkCount":14,"Downtime":"0T00:51:50"}}
06:52:09.425 MQT: tele/home/tasmota_dds238_2/SENSOR = {"Time":"2024-12-18T06:52:09+00:00","ENERGY":{"TotalStartTime":"2024-12-18T06:46:50","Total":10135.194,"Yesterday":24.151,"Today":7.254,"Period":39.8,"Power":2406.6,"ApparentPower":2460.0,"ReactivePower":509.9,"Factor":0.98,"Voltage":218.3,"Current":11.269}}
06:52:14.424 RUL: RULES#TIMER=1 performs "backlog TuyaSend8; RuleTimer1 5"
06:52:14.473 MQT: stat/home/tasmota_dds238_2/RESULT = {"TuyaSend":"Done"}
06:52:14.541 TYA: MCU Product ID: {"p":"sw9asyjj8j44frjl","v":"1.0.0","m":0}
06:52:14.667 MQT: stat/home/tasmota_dds238_2/RESULT = {"T1":5,"T2":0,"T3":0,"T4":0,"T5":0,"T6":0,"T7":0,"T8":0}
06:52:20.398 RUL: RULES#TIMER=1 performs "backlog TuyaSend8; RuleTimer1 5"
06:52:20.425 MQT: stat/home/tasmota_dds238_2/RESULT = {"TuyaSend":"Done"}
06:52:20.493 TYA: MCU Product ID: {"p":"sw9asyjj8j44frjl","v":"1.0.0","m":0}
06:52:20.620 MQT: stat/home/tasmota_dds238_2/RESULT = {"T1":5,"T2":0,"T3":0,"T4":0,"T5":0,"T6":0,"T7":0,"T8":0}
06:52:26.400 RUL: RULES#TIMER=1 performs "backlog TuyaSend8; RuleTimer1 5"
06:52:26.449 MQT: stat/home/tasmota_dds238_2/RESULT = {"TuyaSend":"Done"}
06:52:26.515 TYA: MCU Product ID: {"p":"sw9asyjj8j44frjl","v":"1.0.0","m":0}
06:52:26.643 MQT: stat/home/tasmota_dds238_2/RESULT = {"T1":5,"T2":0,"T3":0,"T4":0,"T5":0,"T6":0,"T7":0,"T8":0}
06:52:28.265 CMD: Rule
06:52:28.273 MQT: stat/home/tasmota_dds238_2/RESULT = {"Rule1":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":94,"Free":417,"Rules":"on System#Boot do RuleTimer1 5 endon on Rules#Timer=1 do backlog TuyaSend8; RuleTimer1 5 endon"}}
06:52:32.405 RUL: RULES#TIMER=1 performs "backlog TuyaSend8; RuleTimer1 5"
06:52:32.454 MQT: stat/home/tasmota_dds238_2/RESULT = {"TuyaSend":"Done"}
06:52:32.521 TYA: MCU Product ID: {"p":"sw9asyjj8j44frjl","v":"1.0.0","m":0}
06:52:32.649 MQT: stat/home/tasmota_dds238_2/RESULT = {"T1":5,"T2":0,"T3":0,"T4":0,"T5":0,"T6":0,"T7":0,"T8":0}
06:52:38.428 RUL: RULES#TIMER=1 performs "backlog TuyaSend8; RuleTimer1 5"
06:52:38.476 MQT: stat/home/tasmota_dds238_2/RESULT = {"TuyaSend":"Done"}
06:52:38.543 TYA: MCU Product ID: {"p":"sw9asyjj8j44frjl","v":"1.0.0","m":0}
06:52:38.670 MQT: stat/home/tasmota_dds238_2/RESULT = {"T1":5,"T2":0,"T3":0,"T4":0,"T5":0,"T6":0,"T7":0,"T8":0}
06:52:44.421 RUL: RULES#TIMER=1 performs "backlog TuyaSend8; RuleTimer1 5"
06:52:44.469 MQT: stat/home/tasmota_dds238_2/RESULT = {"TuyaSend":"Done"}
06:52:44.536 TYA: MCU Product ID: {"p":"sw9asyjj8j44frjl","v":"1.0.0","m":0}
06:52:44.663 MQT: stat/home/tasmota_dds238_2/RESULT = {"T1":5,"T2":0,"T3":0,"T4":0,"T5":0,"T6":0,"T7":0,"T8":0}

I see the command is executed every 5s but not the MQTT result.

[barbudor]

I don't get your point
The logs clearly shows tasmota sending the MQTT RESULT which confirm TuyaSend8 has been performed every 5 seconds

But I believe this is not what you are looking for
Why are you sending this TuyaSend8 message every 5 seconds ? I don't see any requirement for that in the template page

[Stormhand]

RESULT is executed every 5 seconds but tele/home/tasmota_dds238_2/SENSOR is every minute.

[barbudor]

There's no relation.
RESULT is the result of executing the TuyaSend8 command which is just about getting the Tuya device descriptor
There is no reason to send that command every 5 seconds.i don't know where you got that idea from.

SENSOR is totally indépendant and sent at teleperiod
Set your Teleperiod accordingly to what you need

[Stormhand]

I followed this page to flash it https://github.com/krikk/Hiking-DDS238-2-WIFI-Din-Rail-Energy-Meter-flashing-Tasmota and noticed it sends the readings every minute. My goal is to have them every 10s

[sfromis]

As already suggested, set your TelePeriod (minimum 10 seconds).

[Stormhand]

Thank you