Skip to content

alaub81/rpi_pico_scripts

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

51 Commits
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

Raspberry Pi Pico MicroPython Script collection

This is a collection of all my Raspberry Pi Pico MicroPython Scripts.

  • First Steps with Pico LED and Pico's Temperature sensor.
  • Managing the Wifi connection
  • Using Pico as Wifi Access Point
  • Reading from a DHT22 Sensor
  • Reading from a BME680 Sensor
  • Reading from a bh1750 illuminance sensor
  • Controlling a RGB LED
  • first Steps with MQTT
  • Sending Sensor Data to MQTT Broker
  • Sample for logging in python
  • Sample for measuring the time, a script needs to run

You will find a short Description of the Scripts on the top of each script.
If you need support or have questions, just open up an issue, or contact me directly.

You should use Micropython for Raspberry Pico rp2-pico-w-20230228-unstable-v1.19.1-910-g4937174b4.uf2 or later!

Configuration File config.py

most of the Scripts here are using for configuration the config.py file.
There you will configure all the variables which are used in the other python scripts. For example wificonnnection scripts. The SSID, Password, hostname and countrycode is configured in the config.py. Just copy the config_sample.py to config.py, configure it with your needs and then upload it to your Pico.
For details have a look at the comments in the script.

Setup the Pico setup_pico.py

With the setup_pico.py file, you are able to install the follwing libraries:

  • umqtt.simple
  • logging

first the script will connect to wifi (it uses config.py for credentials) then it will install the libraries via mip after that, it just disconnects from wifi.

Autostart Script main.py

To prevent always blank flashing the pico GPIO(19) is used to detect, if the system will break instead of running the MQTT script. Just use a jumper cable to connect GND and GPIO(19) or use a switch on these two pins.

  • On exit you'll see led 5 times flashing (GPIO19 on)
  • on entering the python script led will flash 1 time (GPIO19 off)
  • just put in the name of the python script you like to automaticaly start (in my sample: import dht22homiemqtt.py)

Pico to Wifi wificonnection.py

to make thinks easier, I wrote that littel python script, which is able to connect, disconnect and print out the wifi status. You can use it in other scripts, by just using:

  • wificonnection.connect()
  • wificonnection.disconnect()
  • wificonnection.status()

Installing umqtt.simple or umqtt.robust

for the mqtt Scripts you will need umqtt.simple.
It is not a Standard Library in Micropython for the Pico, so you need to install it once on the Pico. You can use setup_pico.py to install, or just do it step by step.

  • First connect pico to wifi (you can use the wifi_connect_simple.py).
  • Then use the following lines in REPL.
import mip
mip.install('umqtt.simple')
# for the robust variant
mip.install("umqtt.robust")

After installation is done, you can use wifi_disconnect.py to close the wifi connection.

Or just have a look at install_umqtt.py

Deprecated: Installing umqtt.simple2 or umqtt.robust2 via upip

Older Micropython Installation are using upip ... but the newer ones changed to mip

for the mqtt Scripts you will need umqtt.simple2.
It is not a Standard Library in Micropython for the Pico, so you need to install it once on the Pico. First use the wifi_connect_simple.py to connect to your wifi. Then use the following lines in REPL.

import upip
upip.install("micropython-umqtt.simple2")
# for the robust variant
upip.install("micropython-umqtt.robust2")

After installation is done, you can use wifi_disconnect.py to close the wifi connection.

DHT22 Sensor

At first you need to connect your DHT22 Sensor to your Pico's GPIO Board.

Pin Nr GPIO Name DHT22 Sensor
Pin 36 3V3 +3,3V 1 (VCC) / +
Pin 29 GPIO 22 2 (Data)
Pin 28 GND 4 (GND) / -

then you can use the following scripts:

  • dht22_sample.py
    • small Test Script, just run it via REPL
  • dht22homiemqtt.py
    • you need to copy wificonnection.py and config.py to your pico first

More Details here:

BME680 Sensor

At first you need to connect your BME680 Sensor to your Pico's GPIO Board.

Pin Nr GPIO Name BME680 Sensor
Pin 36 3V3 (OUT) VCC
Pin 28 GND GND
Pin 27 GP21(I2C0 SCL) SCL
Pin 26 GP20(I2C0 SDA) SDA

then you can use the following scripts:

  • bme680_sample.py
    • you need to copy lib/bme680.py to your pico first
  • bme680homiemqtt.py
    • you need to copy lib/bme680.py, wificonnection.py and config.py to your pico first
    • and install umqtt.simple on your board.

More Details here:

BH1750 illuminance sensor

At first you need to connect your BH1750 sensor to your Pico's GPIO Board.

Pin Nr GPIO Name BME680 Sensor
Pin 36 3V3 (OUT) VCC
Pin 28 GND GND
Pin 27 GP21(I2C0 SCL) SCL
Pin 26 GP20(I2C0 SDA) SDA

then you can use the following script:

  • bh1750_sample.py
    • you need to copy lib/bh1750.py to your pico first

More Details here:

RGB LED

At first you need to connect your RGB LED to your Pico's GPIO Board.

Pin Nr GPIO Name RGB LED
Pin 15 GP11 R
Pin 16 GP12 G
Pin 17 GP13 B
Pin 18 GND GND

then you can use the following scripts:

  • rgbLED_sample.py
    • sample script to just enable / disable the three colors
  • rgbLED_hexcode_sample.py
    • sample script to play around with hexadezimal color codes:
      • FF0000 (Red)
      • FFD700 (Gold)
      • 00FF00 (Lime)
      • 00FF33 (SpringGreen)
      • 00FFFF (Aqua)
      • 0000FF (Blue)
      • 191970 (MidnightBlue)
      • FF00FF (Magenta)
      • FFFFFF (White)

More Details here:

iPerf3 - Bandwidth testing iperf.py

If you like to know, how fast the wireless connection of your Raspberry Pi Pico is, try the iperf.py Script. It is able to connect to a configured iPerf3 server. You need to copy wificonnection.py and the configured config.py first. On the server side you need to start iPerf3 as a server:
iperf3 -s More Informations about iPerf you can find here:

Installing Logging Library logging

for logging_sample.py you will need to first install the logging Library to your Pico. So connect the pico to wifi and install the Library with mip in the logging_sample.py you will find some examples for logging in different loglevels.

import mip
mip.install('logging')

Measuring execution time with time_measurement_sample.py

If you like to know how much time a script takes for execution, just use the code in time_measurement_sample.py. Or just play around a bit with that sample script.

Links