forked from ToniA/arduino-heatpumpir
-
Notifications
You must be signed in to change notification settings - Fork 0
/
HisenseHeatpumpIR.h
73 lines (60 loc) · 2.31 KB
/
HisenseHeatpumpIR.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
/*
Hisense AQV12PSBN / AQV09ASA heatpump control (remote control P/N zzz)
*/
#ifndef HisenseHeatpumpIR_h
#define HisenseHeatpumpIR_h
#include <HeatpumpIR.h>
// Hisense timing constants
#define HISENSE_AIRCON1_HDR_MARK 9060
#define HISENSE_AIRCON1_HDR_SPACE 4550
#define HISENSE_AIRCON1_BIT_MARK 520
#define HISENSE_AIRCON1_ONE_SPACE 1700
#define HISENSE_AIRCON1_ZERO_SPACE 630
#define HISENSE_AIRCON1_MSG_SPACE 8140
// Power state
#define HISENSE_AIRCON1_POWER_OFF 0x04 //**
#define HISENSE_AIRCON1_POWER_ON 0x00 //**
// Operating modes
// Hisense codes
#define HISENSE_AIRCON1_MODE_AUTO 0x04 // Not available 0x00
#define HISENSE_AIRCON1_MODE_HEAT 0x00
#define HISENSE_AIRCON1_MODE_COOL 0x02
#define HISENSE_AIRCON1_MODE_DRY 0x03
#define HISENSE_AIRCON1_MODE_FAN 0x04
#define HISENSE_AIRCON1_MODE_MAINT 0x04 // Power OFF
// Fan speeds. Note that some heatpumps have less than 5 fan speeds
#define HISENSE_AIRCON1_FAN_AUTO 0x00 // Fan speed
#define HISENSE_AIRCON1_FAN1 0x03 // * low
#define HISENSE_AIRCON1_FAN2 0x02 // * med
#define HISENSE_AIRCON1_FAN3 0x01 // * high
#define HISENSE_AIRCON1_FAN4 0x01 // * high Not available
#define HISENSE_AIRCON1_FAN5 0x01 // * high Not available
// Not available in this model.
// Vertical air directions. Note that these cannot be set on all heat pumps
#define HISENSE_VDIR_AUTO 0
#define HISENSE_VDIR_MANUAL 0
#define HISENSE_VDIR_SWING 0
#define HISENSE_VDIR_UP 0
#define HISENSE_VDIR_MUP 0
#define HISENSE_VDIR_MIDDLE 0
#define HISENSE_VDIR_MDOWN 0
#define HISENSE_VDIR_DOWN 0
// Not available in this model.
// Horizontal air directions. Note that these cannot be set on all heat pumps
#define HISENSE_HDIR_AUTO 0
#define HISENSE_HDIR_MANUAL 0
#define HISENSE_HDIR_SWING 0
#define HISENSE_HDIR_MIDDLE 0
#define HISENSE_HDIR_LEFT 0
#define HISENSE_HDIR_MLEFT 0
#define HISENSE_HDIR_MRIGHT 0
#define HISENSE_HDIR_RIGHT 0
class HisenseHeatpumpIR : public HeatpumpIR
{
public:
HisenseHeatpumpIR();
void send(IRSender& IR, uint8_t powerModeCmd, uint8_t operatingModeCmd, uint8_t fanSpeedCmd, uint8_t temperatureCmd, uint8_t swingVCmd, uint8_t swingHCmd);
private:
void sendHisense(IRSender& IR, uint8_t powerMode, uint8_t operatingMode, uint8_t fanSpeed, uint8_t temperature, uint8_t swingV, uint8_t swingH);
};
#endif